What Size Bolts to Use with HappiJac Extender Bracket for Dual Wheels

Question

Question:

What size bolts do I need to attach these brackets?

asked by: Greg W

0

Expert Reply:

Hey Greg, you would want to go with bolts that are 3/8 inch in diameter with the SwingOut Brackets part # HJ54FR. The bolt holes are all 3/8 inch in diameter. You can also take one of the bolts that are on your setup now to a hardware store and find the exact same diameter and length.

expert reply by: Jameson C

0

Greg W.

10/17/2025

Thanks

Jameson C.

10/21/2025

@GregW Glad to help!

Answer 1

Hey MT! We do have the 9002-7468 just under our part number. What you need is the Brandmotion Tailgate Delete Backup Camera with Wiring Harness - License Plate Mount - Custom Fit #BM67JR. This will allow you to retain the backup camera on your 2022…

view full answer...

Answer 2

Hey Michael, yes you can attach a second set of the extender brackets part #HJ54FR to the Swing Out Extension Brackets part #LC182496 that you asked about.

view full answer...

Answer 3

Hey Jonathan, it's odd but the Happijac Extender Bracket part #HJ54FR does not come with mounting hardware. You'd basically need to take the current hardware from your setup to a hardware store so you can get a duplicate bolt and nut so that…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

From what I can find the Norcold N306.3 fridge has a 2.7 cu ft capacity and is 20-1/8" wide and 26" tall. The most similar option we can offer is the 3.2 cu ft Everchill RV Mini Refrigerator #324-000111. The #324-000111 measures…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Size Bolts to Use with HappiJac Extender Bracket for Dual Wheels

Product Page this Question was Asked From

Continue Researching