Can A Motor Be Added To The Stromberg Carlson Manual Landing Gear Set LG-183708?

Question

Question:

On this LG-183708 can it also be used with a motor. I need to replace my landing gear and my fifth wheel is already set with switches for and electric motor and just want to know if this set up can be used with one.

asked by: Oscar A

0

Expert Reply:

Hello Oscar, thanks for reaching out. Yes, a motor can be added to the Stromberg Carlson Manual Landing Gear Set # LG-183708. You can use really any standard landing gear motor. What I recommend is the following:

- Motor and Switch Kit for Stromberg Carlson Landing Gear - 5,500 lbs # LG-217884

This comes with a motor, wiring harness and switch. So everything you would need to add a new switch to the landing gear system.

expert reply by: Jesse M

0

Motor and Switch Kit for Stromberg Carlson Landing Gear
(click to enlarge)

Answer 1

Sounds like you are looking for a motor to add to your existing landing gear to make them a powered landing gear set. I would have to know what brand of landing gear you have to know for sure what parts you would need. Lippert, Venture and Stromberg…

view full answer...

Answer 2

Hey Cody, we can help but since you have 9-1/2 inches between your current jack mounting brackets nothing we offer would be a direct fit as that is not a standard dimension for jacks made currently. So best option would be a set like the part…

view full answer...

Answer 3

We can get you un-stranded! The correct follow leg for your landing gear is going to depend on how long it is. If your leg measures 29-1/2" (see attached photo), you would need replacement #LG-179014, which can be used with most landing gear…

view full answer...

Answer 4

Lippert made specific replacement landing gear for your 2011 Keystone Montana 5th Wheel. Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear #LC178653 and Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear #LC178652.

view full answer...

Answer 5

Hi James; the better option would be the Bulldog #BD500162 you were looking at. You can add the Motor and Switch Kit for Stromberg Carlson Landing Gear #LG-217884 to the Bulldog which will give it the same functionality as the #LG-4 while saving you…

view full answer...

Answer 6

Hey Hugo, going with a 30 amp MPPT solar charge controller like the part #RS25FR would be the best choice. This is probably rated most ideally for the solar panels you have currently and it's an MPPT style which does a really good job charging…

view full answer...

Answer 7

Hi Shaun, I can definitely help with that. From what we typically see on the 2020 Forest River Wolfpack 365PACK16, the most common landing gear setup is the Lippert/Venture style system with 33-1/2 inch outer tubes and 15-1/2 inch inside-to-inside…

view full answer...

Answer 8

I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the…

view full answer...

Answer 9

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 10

Hi Donny; after looking at several videos of the trailer it does appear to have a 6 on 5-1/2 bolt pattern with ST225/75R15 tires. The Goodyear Endurance ST225/75R15 Radial Tire w/ 15" Eagle Aluminum Wheel #GY97QB will be a direct fit.

view full answer...

Can A Motor Be Added To The Stromberg Carlson Manual Landing Gear Set LG-183708?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching