Is it Normal for an Axle to be Installed Above as Well as Below the Leaf Springs?
Updated 09/30/2025 | Published 09/13/2025
Question:
I have a 10 ft utility trailer and need to replace the 4 leaf slipper springs. The current install has the axle on top of spring, between spring and trailer. Most installed instructions on new springs have the axle between spring and ground. Is either way acceptable?
asked by: Jeff B
Expert Reply:
Hey Jeff!
Yes, the axle can be installed either above the leaf springs or below the leaf springs - it all depends on if the spring seats are located above or below the axle.
I see you ordered the Spring Seat # TRSS175 from us recently. Are you having it welded onto the other side of your axle so you can swap where the axle is installed?
Product Page this Question was Asked From
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Continue Researching
- Search Results: wheel bearings
- Search Results: trailer suspension parts
- Search Results: trailer lights
- Search Results: bronze bushing trailer leaf springs
- Shop: U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
- Search Results: rv vents and fans
- Search Results: roof dome
- Search Results: rv skylight
- Video: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs Review
- Shop: Tandem-Axle Trailer Hanger Kit for Double Eye Springs - 3-1/4" Tall Front/Center/Rear
- Shop: Timken Bearing Kit for 3,500 lb Axles with #84 Spindle - Bearings L44649/L68149
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Wheel Bearing Kit for 1-1/16" to 1-3/8" Tapered Spindle - Bearings L68149/L44649
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Q&A: Hardware for Over-Under Conversion on 3-1/2 Inch Axle
- Video: Review of Specialty Recreation RV Skylight - 14 X 14 Square Smoke Skylight Kit - SR46MR
- Video: Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents Review
- Shop: Camper Tie-Downs
- Shop: Suspension Enhancement
- Video: Spring-Eye Bolt with Locknut for Slipper Springs: The Breakdown
- Video: Review of etrailer Trailer Fenders - Black Plastic Single Axle 3 Step 12 Inch Wheel - HP33RR
- Video: A Closer Look at the Dexter 7-Leaf Slipper Spring w/ Hook End for 8,000-lb Trailer Axles
- Video: Let’s Check Out the 4-Leaf Slipper Spring w/ Open Eye End for 4,300-lb Trailer Axles
- Q&A: What Causes Trailer Equalizer to Be Tilted and Not Flat
- Q&A: Can Tandem Axle Trailer Have a Straight Axle and a Cambered Axle
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
on Trailer Suspension Parts
Jeff B.
9/29/2025
Looks like the current seat is in fine shape so I will not need to install new ones.