Looking for Reverse Lockout Solenoid for Dexter Actuator

Question

Question:

Hello, Im looking for a Reverse Lockout Solenoid for Dexter XR84. Can you help find the correct one?

asked by: Brian

0

Expert Reply:

Hey Brian, the correct reverse lockout solenoid you need for your Dexter actuator would be the part # DX46UR. Did yours fail or are you wanting to add one?

expert reply by: Jameson C

0

Jameson C.

9/2/2025

Hey Brian, did you manage to install the reverse lockout solenoid for your Dexter actuator? I'm curious because your experience might help others who are looking to do the same.

Answer 1

If you want to be able to back your trailer up without the brakes applying you will need the lock out solenoid part #T4748800 with your actuator part #T4079200. Otherwise your brakes will lock up every time your trailer gets reversed.

view full answer...

Answer 2

Out of the available options it does appear that the Model 6 actuator's master cylinders, #T1027100 or #T1777401, are the best and pretty much only options for you. On your master cylinder that additional fitting could be a port for a reverse…

view full answer...

Answer 3

Hey Jeff, we actually have the exact master cylinder you are looking for with the part #T1027100. Since you said you need a damper too the correct replacement shock is the part #T1242600. Damper is another word for shock by the way. For the price of…

view full answer...

Answer 4

Thanks for reaching out, Josh As long as the replacement master cylinder is designed to accept one, yes, you can add a reverse lockout solenoid. With it being an 8,000 lb boat trailer, I'm assuming it has hydraulic disc brakes, which commonly use…

view full answer...

Answer 5

Finding information on the Tie Down 46250 was not an easy task as it was discontinued awhile back. From what I could find, it looks like the calipers marked 46250 often times have to change the mounting bracket and rotor/hub in addition to the…

view full answer...

Answer 6

We do have some options for replacing the Knott calipers and rotors on your Coyote Boat Trailer. We really do not have any info or specs on the Knott brand brakes, but since it is all for a 3,500 lb axle the sizing should be standard. Standard…

view full answer...

Answer 7

Hey Robert! I am sure we have the parts you need to replace your disc brakes, but I am going to need to know what size spindles your Coyote Aluminum trailer has. If you could pull one of your hubs and get the numbers stamped onto the side of both…

view full answer...

Answer 8

Hello Kyle, thanks for reaching out. There are different master cylinders for disc and drum brakes. The part you are looking for Replacement Master Cylinder Assembly for Dexter Model 6 Brake Actuators - Disc #T1777405. The Dexter part number is…

view full answer...

Answer 9

With surge brakes, you have a brake actuator applying the needed pressure to the brakes but to be able to back up you will need to have a manual lockout or an electric lockout solenoid, like #T4748800, which will close when you shift the vehicle into…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Looking for Reverse Lockout Solenoid for Dexter Actuator

Product Page this Question was Asked From

Continue Researching