Should Battery Be Disconnected When Relocating Break Away Switch?
Updated 08/12/2025 | Published 08/08/2025 >
Question:
My trailer came with a trailer break away system on it. I want to remove it temporarily and relocate it. I need to use the trailer after I remove it. Can I just remove the battery and not have the brakes lock up?
asked by: Jeff L
Expert Reply:
Hi Jeff!
A break away switch, like the Curt Trailer Breakaway Kit # C52042, basically just completes a circuit that then powers the electric brakes. If you are removing it to relocate the switch and or trailer, you will want to completely disconnect the battery from the trailer. That way there is no way it can supply power to the brakes.
Where is it now and where are you wanting to relocate it to?
Product Page this Question was Asked From
Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-Axle
- Tandem-Axle
- Triple-Axle
- LED Indicator
- Electric
- Battery Included
- 5 Ah
- 51 Inch Long
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Dexter Trailer Hub and Drum Assembly for 2,000-lb Axles - 7" - 5 on 4-1/2
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Shop: Replacement Bearing Kit with Bearings L44649, Races L44610, Seal 10-9 - Fits 1.063" Spindles
- Shop: Lippert Spindle Nut Kit w/ Round Washer - For 2,200-lb to 4,400-lb Axles
- Search Results: bearing
- Shop: Dexter Trailer Hub and Drum Assembly for Hydraulic Brakes - 2,000-lb E-Z Lube Axles - 5 on 4-1/2
- Shop: Grease Seal - Double Lip - I.D. 1.719" / O.D. 2.565" for 3.5K and 4.4K Axles - Qty 2
- Shop: Grease Seal - Double Lip - I.D. 1.500" / O.D. 1.987" - 2,000-lb to 2,500-lb Axles - Qty 1
- Shop: Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Side Load
- Q&A: How to Wire a Breakaway Switch to the Trailer Battery
- Q&A: How To Wire the Curt Push-To-Test Trailer Breakaway Kit
- Video: Curt Push-To-Test Trailer Breakaway Kit Installation - 2017 Grand Design Solitude Fifth Wheel
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Q&A: Does Brake Controller Need Separate Fuse if Install in 2016 Chevy Colorado with Factory Tow Package
- Article: How to Wire an Electric Winch
- Video: Breaking Down the LED Clearance or Side Marker Trailer Light w/ Reflector
- Q&A: Replacement Hub Drums for AL/KO 8440 and Compatible Brake Assemblies
- Q&A: Parts Needed to Add Brakes to 1992 Coleman Arcadia Pop-Up Camper
- Search Results: 4 wire wiring
- Search Results: 7 pin connector
- Search Results: 7 pin junction box
- Video: etrailer 7 Way Upgrade Kit With Junction Box Installation
- Q&A: What Wire Gauge Is The TowSmart 16 to 18 Gauge, 4 Conductor Wire?
- Search Results: electric brake wire
- Search Results: amber reflector
- Search Results: tekonsha trailer breakaway kit
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Video: Review of CURT Trailer Breakaway Kit - Kit with Push Test Charger - C52042
- Q&A: Comparing Trailer Breakaway Switch Kits


Jeff L.
8/12/2025
Thank you for the direction. It is on the floor in the V Nose now and I will move it to the top of the V Nose.