How To Wire the Curt Push-To-Test Trailer Breakaway Kit
Updated 03/23/2020 | Published 03/21/2020
Question:
Well the instructions that come with this unit, pretty much suck. Switch does not have 2 black wires Blue on left/ Black on right, Panel has no yellow wire White/ Red/ Blue. Wired to what I read from the diagram and I have power the breaks.
asked by: David S
Expert Reply:
In regards to the Curt Push-To-Test Trailer Breakaway Kit part # C52042, the blue wire on the breakaway switch will be run to the brake output circuit and the black wire to a constant 12 volt power source. The blue wire on the battery box will also will be run brake output circuit, the red wire to a 12 volt power source, and the white wire to a ground.
Product Page this Question was Asked From
Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-Axle
- Tandem-Axle
- Triple-Axle
- LED Indicator
- Electric
- Battery Included
- 5 Ah
- 51 Inch Long
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: 440l peterson square trailer tail light
- Search Results: trailer light guard
- Search Results: tie down anchors
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Testing Trailer Brake Magnets for Proper Function
- Shop: Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Side Load
- Q&A: Recommended D-Ring Tie-Down Anchor For With An Endless Loop
- Article: Trailer Maintenance Schedule
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Video: In-Depth Review of the Light Guard
- Video: Comprehensive Review: Replacement Trailer Brake Magnet for Dexter Electric Brake Assemblies
- Video: etrailer Easy Grease Trailer Hub and Drums Installation - 2020 K-Z Sportsmen Classic Travel Trailer
- Video: etrailer Electric Trailer Brakes Review
- Search Results: curt trailer breakaway kit
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Wiring
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Video: Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor Feature Review
- Video: Trailer Breakaway Kit Battery Charger Review
- Video: Review of ABS Fasteners Tie Down Anchors - Trailer and Truck Tie-Down Anchors - ABS69FR
- Search Results: 7 pin wiring harness
- Article: The Best Trailer Tongue Locks for Preventing Trailer Theft
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: Buyers Products Tail Light Mounting Box - 4" Round Hole - 2-5/16" Round Hole - Black Steel
- Shop: Light Guard - Unpainted Steel for 440 Tail Light
- Shop: etrailer Trailer Tool Box - A-Frame - Aluminum - 3.4 Cu Ft - 34" Long - Matte Black
- Shop: Brake Controller
- Q&A: Troubleshooting Trailer Wiring Connections on 2003 Chevy Silverado 4x4
- Q&A: How To Move A Trailer With A Dead Breakaway Battery
- Q&A: Breakaway Kit Not Working Properly and Causing Issues with my Brake Controller
on Trailer Breakaway Kit
