Do You Have a Replacement Axle Rated for 2K with 72" Hub Face and 59 1/2" Spring Center?

Question

Question:

Hi My trailer axle rated at 2000 lb - 4 bolt 72/59.5 would there be a replacement for it ?

asked by: Philip

0

Expert Reply:

Hello Philip,

We don’t have an exact match for your specifications. The closest option we carry is the axle you were looking at: Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern - 72" Long - 2,000 lbs # e62YR. The 72" hub face matches your requirement, but the spring center is 58", not the 59.5" you’re looking for.

You could still make it work by welding on new spring seats, such as part # TRSS175.

What kind of trailer is this going on?

expert reply by: Kate F

0

Axle Dimensions
(click to enlarge)

Philip

8/12/2025

It’s a 18ft boat trailer.

Kate F.

8/13/2025

@Philip You can usually get away with the hub face being slightly different, but the spring center needs to be precise since that is where you frame is going to sit. Just got our boat back 3 weeks ago after having to wait on a new motor for 7 weeks, the unexpected "bill out another thousand (boat)" is never fun, but worth it when you have those tight lines!

Answer 1

The replacement you would need for your trailer axle that measures out to be 72 inches from hub face to hub face and is 60-1/2 inches from spring center to spring center you will need is The Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72…

view full answer...

Answer 2

I'd be more than happy to help you out! If you can measure the hub-face and spring-center measurements of your current axle that will help me know what you're needing. For example, the etrailer Trailer Axle with Idler Hubs #e65GR has a…

view full answer...

Answer 3

I would be happy to help you determine the correct replacement axle for your 2000 Bass Tracker Pro Team 175 and Trailstar trailer but the axle length is actually measured hub face to hub face so you will want to put your hubs back on temporarily and…

view full answer...

Answer 4

Hey Brianna, we have almost all of the info needed to pick out a trailer axle for your trailer but the last piece of info we need is the weight capacity of the axle. This should be listed on the tag on the axle that you found the serial number on.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Do You Have a Replacement Axle Rated for 2K with 72" Hub Face and 59 1/2" Spring Center?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching