How Do You Get The Hub Face Measurement On An Axle?
Updated 08/07/2025 | Published 07/14/2025
Question:
CAN U TELL ME HOW TO MEASURE THE HUB FACE TO HUB FACE AXLE?
asked by: Angelo L
Expert Reply:
Hey Angelo,
Absolutely! The best way to measure your hub face on your axle is to measure from the outer edge of one hub face to the outer edge of the other hub face. I have attached a photo that shows better how to do that.
If for any reason it is easier to without the hubs, or you do not have them on you can also measure from brake flange to brake flange, and then add 6" to accommodate where the hubs would sit (3" on each side).
I have attached an article as well that walks through how to get that measurement. Let me know if you have any questions about it. What kind of trailer do you have?
(click to enlarge)
Product Page this Question was Asked From
Trailer Axle Beam with Easy Grease Spindles - 89" Long - 5,200 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 5200 lbs
- Spindles Only
- 74 Inch Spring Center
- 89 Inch Hub Face
- No Drop or Lift
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: hydraulic brake hose
- Search Results: brass brake line fittings
- Search Results: brake line tee
- Search Results: hydraulic brake line
- Search Results: brake hose
- Search Results: flexible hydraulic brake lines
- Search Results: standard equalizer trailer suspension parts
- Shop: Demco Surge Brake Actuator - Drum - 2-5/16" Ball - Primed - 12,500 lbs
- Shop: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Article: How to Measure a Trailer Axle
- Shop: U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7-1/16" Long U-Bolts
- Video: Demco Hydraulic Brake Actuator-DM8101802 Feature Review
- Q&A: What Is The Correct Oil To Use In My Dexter Axles With Oil Lube Bath Hubs?
- Shop: EZ Lube Grease Caps with 1.99" OD - Fits 7" and 10" x 1-1/4" Dexter Hubs - Qty 2
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Dexter Hydraulic Brake Line with Fittings - 17-3/4" Long
- Q&A: Should Leaf of Trailer Leaf Spring be Removed to Lower Capacity
- Q&A: Replacement Leaf Springs for 2022 Grand Design Solitude With 7k Axles
- Q&A: Replacing 6-Way on Trailer With 7-Way Connector
- Q&A: Coupler Lock for an Atwood Gooseneck
- Q&A: Best Brake Controller For 2025 Ford F250 With Factory 7-Way
- Q&A: Correct Replacement Jack for Kwikee Level Best 3000 Hydraulic Leveling System
- Article: Trailer Wiring Diagrams
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Raise Your Travel Trailer Height
- Article: How to Tell the Weight Rating of a Trailer Axle
Nick S.
8/7/2025
Hey Angelo, How did measuring the hub face to hub face on your axle go? Did the method I shared work well for you? If you need more help, just let me know!