Is the Opti-Brite LED Strip Light for RVs ILL78CBB Dimmable?

Question

Question:

Is this unit dimmable?

asked by: Martin C

0

Expert Reply:

Yes, it is Martin! The Opti-Brite LED Strip Light for RVs item # ILL78CBB is indeed dimmable so long as you use a dimmer switch like the RV LED Light Side-Slide Dimmer Switch - Black Item # 37205-12315.

Where are you planning on mounting this light?

expert reply by: Jerred H

0

Jerred H.

8/7/2025

Hey Martin, how did it go with mounting the Opti-Brite LED Strip Light? Did the dimmer switch work out for you? I'm curious because it could help others who are setting up similar lighting.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

Hey Jesse, cool name! That's definitely a custom project, and there isn't a single off-the-shelf kit that'll give you everything you need. For a lift-up wall that's around 10' x 6', you're looking at building the door and…

view full answer...

Answer 12

We sure do Brian. We've actually got two center caps that are going to work with the Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Black Aluminum Wheel item #KE58JV. Which one you go with is going to come down to personal…

view full answer...

Is the Opti-Brite LED Strip Light for RVs ILL78CBB Dimmable?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching