Availability of Replacement Fender for Malone MegaSport Kayak Trailer

Question

Question:

Does Malone autoracks sell the megasport fender assembly as a replacement part?

asked by: William R

0

Expert Reply:

Hey William! What happened to your fender? Malone does have a replacement fender available for the MegaSport Kayak Trailer # MPG535. The fender is the Replacement Galvanized Fender for Malone MegaSport Trailers # MAL43DR. If you need the mounting bracket as well that is the # MAL63DR.

expert reply by: Robin H

0

MegaSport Fender
(click to enlarge)

Robin H.

9/2/2025

Hey William, did you end up getting the replacement fender for your MegaSport Kayak Trailer? I'm curious to know how it worked out for you, as it could help others who might be in the same situation.

Answer 1

The VIN sticker that comes with the Malone trailers like the Microsport part #MPG460G is supposed to be applied up near the coupler of the trailer on the frame. It comes as a separate decal though so it's up to you where to put it.

view full answer...

Answer 2

VIN numbers are sometimes difficult to find on trailers as there is not a specific required position but they are usually imprinted somewhere in the metal. They can be posted anywhere along the frame rails, but most often are found near the coupler.…

view full answer...

Answer 3

The VIN sticker for the Malone MPG585XB EcoLight trailer which we offer as #MAL73FR should have been included along with the registration paperwork. The VIN sticker is placed on the same sheet that has the tire load information sticker that looks…

view full answer...

Answer 4

The standard plate to put the VIN sticker of the Malone Microsport Lowbed Trailer Model #MPG460G is on the frame of the trailer. Since the tongue of this trailer is removable I put it further back than that on the portion of the frame that splits off…

view full answer...

Answer 5

Yes the lug nuts #LHLR103 that you referenced are a fit on the Malone MicroSport trailers.

view full answer...

Answer 6

Sorry to hear about that! The wheel studs part #K12WB169 would be what you'd need for the hub of your rebranded Malone MicroSport Trailer #MPG460G that you referenced. Hopefully karma catches up with that guy.

view full answer...

Answer 7

We actually carry the spare tire that fits the Malone MicroSport Trailer #MPG460G. The spare is #MPG465 and does have a 5 on 4-1/2 bolt pattern. With that being said it would be more cost effective for you to purchase two 4.80-12 trailer tires, like…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...