What is A-Frame Jack with Best Ground Clearance

Question

Question:

Need A frame trailer jack with high ground clearance . 2000 lb wont work. Bottom scrapes pulling in driveway. Camper is 2800 lb. Can you recommend anything else.

asked by: Kenneth B

0

Expert Reply:

Hey Kenneth, the A-frame jack with the best ground clearance is the Ultimate Trailer Jack part # 322-RDJ-2k Which actually lets you select how much of the jack's outer tube fits down below the mounting plate. So it can require basically zero ground clearance if that's what would work best for you.

expert reply by: Jameson C

0

Ultimate Trailer Jack Install
(click to enlarge)

Jameson C.

9/12/2025

Hey Kenneth, did the Ultimate Trailer Jack work out for your camper's ground clearance issue? I'm asking because your experience could really help others facing the same problem.

Answer 1

I looked through all of our available manual A-Frame trailer jacks and the option with the shortest retracted bracket height is the etrailer.com A-Frame #TJA-2001-B. The retracted bracket height is right at 5-1/8 inches from the ground and it has a…

view full answer...

Answer 2

The distance from the bottom of the mounting flange to the bottom of the outer tube on the Bulldog Round, A-Frame Jack part #BD155033 is 3-1/2". The mounting flange is 3/16" thick. I have attached a photo of these measurements for you as…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

What is A-Frame Jack with Best Ground Clearance

Products Featured in This Question

Continue Researching