Distance Between Mounting Holes on Replacement L-Bracket for HappiJac Truck Camper Jacks

Question

Question:

I need to know the bolt hole spacing on the jack mount side 3-Hole side. I have an Atwood jack mount plate that bent.

asked by: Todd J

0

Expert Reply:

Hey Todd, all of the mounting holes on the 3-hole side of the Replacement L-Bracket part # LC182492 are separated by 7 inches.

expert reply by: Jameson C

0

Jameson C.

9/12/2025

Hey Todd, did the Replacement L-Bracket with the 7-inch hole spacing work out for your Atwood jack mount plate? I'm asking because your experience could help others facing a similar issue.

Answer 1

I wasn't sure if you were referring to the flat bracket or the L bracket, so I included both, just to cover everything. Both of these are 16" tall and will work with your HappiJac set up. Replacement L-Bracket for HappiJac Truck Camper Jacks…

view full answer...

Answer 2

It sounds like what you are looking for is the MB Sturgis Quick Disconnect Propane Hose for Small Appliance, #100476-72-MBS. This is a 6' hose that has a 1/4" Male QD on one end with a 1by 20 on the other that connects to the Buddy Heater in…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Distance Between Mounting Holes on Replacement L-Bracket for HappiJac Truck Camper Jacks

Product Page this Question was Asked From

Continue Researching