Replacement Dual Locking Pin for Weigh Safe Ball Mount

Question

Question:

Hi I purchased one of you aluminum 2 ball hitches with 3inch shaft. The lock and dual pin mechanism was stuck / seized and I ended up breaking the lock. Wondering if I can buy a new one just the lock/ pins main hitch and balls are fine. thanks Ian

asked by: Ian M

0

Expert Reply:

Hey Ian! You can use the Replacement Dual Locking Pin for Aluminum Weigh Safe & 180 Hitches, Cerakote # WS43VR or Replacement Dual Locking Pin for Aluminum Weigh Safe & 180 Hitches # WS94CR for a replacement. If you need anything else let me know in the comments below.

expert reply by: Robin H

0

Ian M.

4/29/2025

OK thanks Robin, I didn't see this on your website as I was likely not looking in the correct location. I will place an order thanks Ian

Robin H.

4/29/2025

@IanM not a problem, it isn't even listed on related parts for the ball mounts and it should be. I could only find the one without Cerakote because it was linked at the bottom of the page for the one with Cerakote. I hate to say it but our site can be a little difficult to navigate sometimes.

Ian

4/29/2025

@RobinH Well all good with your help. I ordered it Thanks

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Dual Locking Pin for Weigh Safe Ball Mount

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching