Tie Down Recommendation for 2007 Ford F-350 and 3,400 lb Camper

Question

Question:

I have a 2007 F-350 single rear wheel long bed. Could I get a recommendation on anchors for a 3400lb camper?

asked by: Alex E

0

Expert Reply:

Hey Alex, for your 2007 Ford F-350 single axle long bed I would go with a frame mounted tie down like the Torklift part # TL93VV which is a front and rear set confirmed to fit your truck. This will be much more secure and stable than a bed mount and has the extra capacity you'd need for the weight of your camper.

expert reply by: Jameson C

0

Jameson C.

10/30/2025

Hey Alex, how did the TorkLift frame-mounted tie downs work out with your F-350 and camper setup? Your experience could point others in the right direction.

Alex E.

11/4/2025

The mounts worked out great! exact fit and took about 4 hours to install by myself with basic socket set and a torque wrench @JamesonC

Jameson C.

11/4/2025

@AlexE Nice! Glad it went well and you like them!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 10

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey David, thanks for reaching out. Yes, the Curt Trailer Hitch Receiver #C82RJ will indeed fit the 2027 Kia Telluride. This hitch is still in the pre-order phase, but it is being going to fit both the 2026 and 2027 Telluride. Right now, we are…

view full answer...

Tie Down Recommendation for 2007 Ford F-350 and 3,400 lb Camper

Product Page this Question was Asked From

Continue Researching