How to Address a Sagging Issue w/ a 9,500 lbs Trailer and a Toyota Sequoia

Question

Question:

I have a 2023 Toyota Sequoia Capstone that I use to tow a 32 foot travel trailer. The Toyota can tow 9500 lbs, and my trailer is 7300 lbs dry. In a recent trip from CA to Grand Canyon I noticed some sag. Do you recommend air bags or anything else to help stabalize the ride?

asked by: Roy M

0

Expert Reply:

Hey Roy, that sounds like a fun trip! I recommend addressing your sagging issue with a weight distribution system not air bags. The best one for your trailer is going to be the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item # EQ37140ET. This system works with tongue weights ranging from 1,000 lbs - 1,400 lbs so it'll be perfect for your trailer when loaded.

The Equal-i-zer item # EQ37140ET works by distributing the weight more evenly to the tow vehicle. This is how the sagging issue will be addressed. Rather than the weight being centered on the coupler, where the trailer and vehicle connect, the weight distribution hitch distributes the weight across the axels of the vehicle and the trailer.

As an added bonus, item # EQ37140ET has built in sway control that will keep your trailer in line with your Sequoia. This is helpful when you're making a sudden lane change, get passed by a semi, or encounter a strong gust of wind. This will be extremely useful when traveling in California due to the high winds in certain areas.

I have linked a faq below that will give you some more information on weight distribution hitches. Feel free to email me directly or comment below with any additional questions.

expert reply by: Jerred H

0

Roy

1/15/2025

I forgot to mention I did have a weight distribution system. Its the Equilizer as the one you suggested.

Jerred H.

1/15/2025

@Roy That's going to be the best way to go. I recommend going back and making sure it was set up properly and checking to see if it fits the capacity of your trailer's tongue weight.

Roy

1/15/2025

@JerredH It was set up by Giant RV in Murrieta,

Jerred H.

1/15/2025

@Roy I am not familiar with them or their work, but I recommend looking at the instructions below and setting it up yourself. What capacity system do you have?

See All (4) Replies to Roy ∨

Answer 1

With the Timbrens there isn't a difference in fitment between standard model Tundra's and the TRD Pro so you'll be able to use one of the following options for your rear suspension: 4,800lb capacity #T83MR 6,000lb capacity #T45MR 7,000lb…

view full answer...

Answer 2

Hey Mark, I recommend going with the kit you looked at, which is Timbren Suspension Enhancement System - Rear Axle #T45MR along with Spacer Kit #T68MR. If you had a camper on the bed, or had the rear end maxed out all the time, then I'd recommend…

view full answer...

Answer 3

Hey John, so the 2024 Toyota Tacoma is a new designed truck so they currently only have a 2WD version fit with the part #F2410. For 23' the 4WD fit version is the #F2407 but it hasn't been carried over to the 24' models. Right now all we…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

How to Address a Sagging Issue w/ a 9,500 lbs Trailer and a Toyota Sequoia

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching