Recommended Mounting Cover for TecNiq Mini LED Accent Lights

Question

Question:

How would you mount these lights? Are there any mounting plates or grommets available that they would fit in?

asked by: Brian

0

Expert Reply:

Hey Brian! To mount the Mini Rectangular LED Boat Accent Light item # TN27FR you'll want to use one of the following covers:

Horizontal - Mounting Cover for TecNiq Mini LED Accent Light item # TN94FR

Vertical - Mounting Cover for TecNiq Mini LED Accent Light item # TN44FR

expert reply by: Jerred H

0

Jerred H.

11/3/2025

Hey Brian, how did the mounting go with the Mini LED Boat Accent Lights using the covers you picked? Your update could make it easier for the next person setting up the same lights.

Brian

11/3/2025

@JerredH I used the horizontal black cover and they worked really well. The lights jiggled inside the cover just the slightest bit so I added a small piece of rubber gasket material behind the light and it’s a snug fit now. Probably not even necessary to use the gasket.

Jerred H.

11/3/2025

@Brian Glad you got it working!

Answer 1

Hello Jacob, thanks for reaching out. Yes, the Dragon Oval LED Boat Accent Lights like part #TN47VR are dimmable with an LED compatible dimmer switch.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

From what I can find the Norcold N306.3 fridge has a 2.7 cu ft capacity and is 20-1/8" wide and 26" tall. The most similar option we can offer is the 3.2 cu ft Everchill RV Mini Refrigerator #324-000111. The #324-000111 measures…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Recommended Mounting Cover for TecNiq Mini LED Accent Lights

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching