Recommended Yakima Fit Kit for a 2024 Toyota Tacoma

Question

Question:

Hi. Does Yakima make a Landing Pad kit for the 2024 Tacoma? Thanks.

asked by: Frank

0

Expert Reply:

Frank, yes they do. What you're going to need is the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06180 which will work with the BaseLine towers and comes with the clip and landing pads.

If you're looking for something else, feel free to let me know.

expert reply by: Bryce D

0

Frank

1/3/2025

I was inquiring about the Landing Pad type attachment (like the Landing Pad 24 for the 3G Tacoma) the bolts to the factory attachment points in the roof gutter. Thanks. Frank

Bryce D.

1/6/2025

@Frank Frank, I did some research and it does not look like there is a landing pad for the 2024 Toyota Tacoma. Yakima does not have the SkyLine or Control towers for that truck, so there aren't any landing pads. They only make the fit kits that are for naked roofs, like the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06180 from what I could find.

Answer 1

While there are not instructions available for removing the Yakima BaseLine Towers Y00146 from your 2016 Honda Civic I would be happy to walk you through the removal process. This will require the tightening tool that was included with your BaseLine…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

There is a wiring kit for a brake controller Preston but it's not going to be a plug and play one. The 2025 Toyota Tacoma does not have a plug in brake controller port. Toyota stopped putting them in after the 2023 model. For your Tacoma, I…

view full answer...

Answer 6

Hey Sean, yes you can use the TowSmart Adjustable Ball Mount #TS89VR in the Gen-Y Voyager Ball Mount #GY52JJ. This will provide cushioning to the adjustable ball mount plus some additional drop. What are you planning on towing with this setup?

view full answer...

Answer 7

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Howdy Jason, for trailers over 6-1/2 feet wide, you’ll want either #e97XV 5 foot ramps or #e67XV 6 foot ramps. Both bolt directly to a wood trailer deck and include everything needed for installation. Between the two, ramp length is the deciding…

view full answer...

Answer 12

Hey Todd! Yes, the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack w/ Tonneau Cover Adapters #Y01151-5755 is compatible with the Synetic MR Retractable PRO Tonneau Cover on your 2025 Toyota Tacoma. The adapters will fit the T-slot rails on that…

view full answer...

Recommended Yakima Fit Kit for a 2024 Toyota Tacoma

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching