Do You Have Mounting Brackets for a Dexter Torsion Axle?

Question

Question:

Im looking for torsion axle mounting brackets. I have a 2007 moritz 14.5 gvw gooseneck with 7k torsion axles. Needing to replace the brackets welded to the frame due to some bad rust from out pa winters and salt. Any help would be greatly appreciated. Thank you.

asked by: Steve A

0

Expert Reply:

Hey Steve! I am sorry but we do not have the mounting brackets you need for a 7,000 lbs Torsion Axle. That's going to be a #12 torsion axle and all we have the mounting brackets for are the #10 item # DX54FR and the #11 item # DX57FR.

expert reply by: Jerred H

0

Jerred H.

12/15/2025

Hey Steve, were you able to find replacement brackets for your 7K torsion axles? Knowing what worked could help others trying to fix similar rust issues on their trailers.

Answer 1

For your horse trailer with Dexter Torflex 3500 lb axles, you will need the Torflex Lift Kit - Tandem Axle - 2-5/8" Lift #K71-707-02 along with two sets of the Dexter Axle Torflex #10 Axle Side-Mount Frame Installation Hardware Kit #DX54FR which…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Do You Have Mounting Brackets for a Dexter Torsion Axle?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching