Where Are The Kenda Tires KE43KV Manufactured?

Question

Question:

Were are these tires manufactured?

asked by: Bob

0

Expert Reply:

Hello Bob, thanks for getting in touch. The Kenda tires like the # KE43KV you mentioned are made in either Taiwan, Vietnam, China or Indonesia. Each tire has a plant code that shows where it was made. Virtually all trailer tires these days are made overseas and it does seem like the quality of these tires is improving over the years.

expert reply by: Jesse M

0

Answer 1

The conventional trailer wheel part #AM20504 that you referenced is 6 inches wide and the tire size you mentioned needs a wheel width of between 6 and 7 inches. You could fit a 225/75-15 tire size would work great on the #AM20504.

view full answer...

Answer 2

I'll start off by saying that when it comes to wheels that are rated for the weight of your trailer and are 15" wheels with a 5 on 4.5 bolt pattern, we have a very limited selection of wheels that have a +0.5 offset (which is the largest…

view full answer...

Answer 3

Hi Carl; the saddle attachment on the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR is 3-1/4" wide at the base of it before the sides flare out. What will you be using the jack for?

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Where Are The Kenda Tires KE43KV Manufactured?

Product Page this Question was Asked From

Continue Researching