Where are Romik Running Boards Made

Question

Question:

are these steps made in the USA

asked by: Charles

0

Expert Reply:

Hey Charles, no the Romik RB2 Running Boards w/ Custom Install Kit # RMK25PR not made in the USA- they are made in Austria.

expert reply by: Bryce D

0

Robin H.

12/15/2025

Hey Charles, were you able to find a set of running boards made in the USA that fit your needs? Knowing what you chose could help others looking for American-made options.

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 3

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 4

Hello Fred, thanks for reaching out. We do have brake controllers that can be used on your 2025 Ford Ranger, but I am sorry to say we do not have anything with a custom pigtail for the factory under dash EBC plug. All of the options we have at this…

view full answer...

Answer 5

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 6

Hey Tom! I personally like the etrailer Hitch #e37ZV because it has a matte black finish that protects the metal better than a standard glossy black finish, but I see you picked up the Draw-Tite #DT35PR which is also a great hitch that I know…

view full answer...

Answer 7

Hey Gary, yes, we do have a base plate for your 2025 Ford Ranger! What you'll want is the Roadmaster Direct-Connect Base Plate Kit #RM23DQ. This base plate has removable arms, has hidden brackets for a non-obtrusive design, and has a simple…

view full answer...

Answer 8

Good question Matt, you've definitely done your homework! Yes, your understanding is correct. The Replacement Fast Grip Clamp #TH94JV is the same mounting clamp used on the Thule Pulse Large cargo box #TH615. The FastGrip clamps are designed to…

view full answer...

Answer 9

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire…

view full answer...

Answer 10

Hi Jeff! I have everything you need to get your 2025 Ford Ranger Raptor set up for flat towing below. I did go with the heavier tow bar as your curb weight (right about 5,400 pounds) was getting a little too close to the capacity of the smaller…

view full answer...

Answer 11

Hey Jacques, thanks for reaching out! The Redarc Tow-Pro Liberty #RED52VR will work just fine on your 2023 Ford Ranger, and it will install by splicing into a bundle of wires under your driver side dash. We have a video of this same process of the…

view full answer...

Answer 12

Hey Asa! I totally see where you're coming from, and I can see why it would be confusing. The gray plug will plug in at the back of your 2024 Ford Ranger, and then the black wire from the Curt T-Connector #C96GJ will need to draw power directly…

view full answer...

Where are Romik Running Boards Made

Product Page this Question was Asked From

Continue Researching