What Ball Mount is Needed for 8 inches of Drop

Question

Question:

@JamesonC the distance from the bottom of the coupler lip down to the ground is 23". The distance from the top of the hitch opening down to the ground is 14 3/4". The top of the hitch itself is 15". Thanks

asked by: Travis

0

Expert Reply:

Hey Travis, based on those numbers you'd need a drop of about 8 inches like the Curt # C45338.

expert reply by: Jameson C

0

Travis

11/12/2024

Would an 8" rider negatively impact my 5,000lb tow capacity or my 500lb tongue weight limitations?

Jameson C.

11/12/2024

@Travis No, ball mounts with more drop don't affect the tongue weight capacities of the hitch.

Answer 1

The second pin hole of the Curt ball mount part #C45240 that you referenced is 3 inches behind the first one. That means the second pin hole is 6-1/4 inches from the weld bracket.

view full answer...

Answer 2

Just to make sure we are accurate on the actual rise you may need, lets cover some basics. With the tow vehicle parked on level ground, measure from the ground to the top of your hitch receiver opening. Then, with the trailer level, measure from the…

view full answer...

Answer 3

Hi Daniel; the BAJA Collection Ball Mount w/ 2" Ball and Hitch Pin - 5-1/4" Drop - 4" Rise #TS27VR is the best option for what you need. However, it won't come pre-torqued in the rise configuration so you will have to install the…

view full answer...

Answer 4

The Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2" Hitches #ERT00108 requires at least 1" of the shank to properly fit. I went out and measured the shank on the Curt Adjustable 2-Ball Mount #C99NR and found the from the center of…

view full answer...

Answer 5

Hey Art, we can help but we don't have a ball mount that has the ball pre-installed and torqued in the configuration you are wanting. So you would want to start with a ball mount that has a 4 inch rise like the TowSmart #TS78FR and then add a 2…

view full answer...

Answer 6

It sounds like you're looking for the distance from the center of the hitch pin hole to the center of the ball on the Curt Adjustable 2-Ball Mount #C99NR. That measurement is 12-1/4".

view full answer...

Answer 7

Hello Paul, The weight of the BulletProof Hitches Aluminum Adjustable 2-Ball Mount - 2" Hitch - 4" Drop/Rise - 14K #BPH97MR is about 17 pounds. We have the shipping weight listed as 17.803 pounds. Is that weight going to work for you? (You…

view full answer...

Answer 8

Hey Javier, unfortunately Bulletproof does not have a combination 1 7/8" and 2" ball mount. What you could do though, is use the B&W Tow & Stow 3-Ball Mount #BWTS10048B which also has a 10k capacity, 5 1/2" of rise, 5" of…

view full answer...

Answer 9

When determining the amount of rise or drop you will need on the ball mount for your towing setup, you just need to take a couple simple measurements. The first, which you have already taken, is from the ground to the top of the trailer hitch…

view full answer...

Answer 10

Thanks for the picture! The Curt Trailer Hitch item #C13277 you referenced is confirmed to fit your 2017 Audi Q7. This hitch is custom fit and bolts to your Audi with included hardware. To be level you will typically want your ball mount to be within…

view full answer...

Answer 11

I have just what you need, the Curt Ball Mount part #C45338 which has a 7" rise and is designed for a 2" trailer hitch. This is a fixed ball mount but we have adjustable options, the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount part…

view full answer...

Answer 12

Hey Jonathan, you are correct. The etrailer Adjustable Ball Mount #E66PR has been tested on a 2024 Nissan Frontier and because the hitch receiver sits too far inside (only 3" from hitch pin hole to bumper), this ball mount will hit the bumper…

view full answer...

What Ball Mount is Needed for 8 inches of Drop

Product Page this Question was Asked From

Continue Researching