Does Etrailer Adjustable Hitch E66PR Fit 2024 Nissan Frontier With OEM Receiver?

Question

Question:

Will the etrailer adjustable trailer hitch e66PR work in the rise position on my 2024 Nissan Frontier? I was told it may hit the bumper because the frontiers OEM hitch sits too far in.

asked by: Jonathan

0

Expert Reply:

Hey Jonathan, you are correct. The etrailer Adjustable Ball Mount # E66PR has been tested on a 2024 Nissan Frontier and because the hitch receiver sits too far inside (only 3" from hitch pin hole to bumper), this ball mount will hit the bumper when trying to line up the hitch pin holes for installation (see photo). You can use this in the drop position without an issue.

The aftermarket receivers available for the 2024 Frontier don't offer more clearance, so your only solution is to install a hitch extender like Curt Hitch Extender 8" Long # C45791 (this reduces hitch capacity by 25%) or to install a ball mount with a shank that has a hitch pin hole to ball mount distance greater than 3" like with Curt # C45900, which offers about 4-1/8" of clearance in that regard.

expert reply by: Andrew N

0

Hitch Pin Hole To Shank Measurement
(click to enlarge)

E66PR hitch pin hole on Nissan Frontier OEM receiver
(click to enlarge)

E66PR pin hole measurement
(click to enlarge)

Answer 1

Speed is a huge issue with trailer tires actually. Unless otherwise noted trailer tires are rated as 65 miles per hour as their max speed. Exceeding the speed rating will cause the tire to heat up and fail easier. We do have a couple brands that have…

view full answer...

Answer 2

Thanks for reaching out! I have two options for a trailer hitch for your 2018 Audi SQ5. The first is the etrailer #e94CR. This Class III hitch has a 2" receiver and a bolt-on installation. It has a concealed cross tube, so only the receiver will…

view full answer...

Answer 3

You will still be able to use the trailer with the 4-Way after installing the 4 to 5-Way adapter, #20036. First, you could just remove the adapter if you wanted to and then plug in the 4-Way like normal while stowing the adapter in the truck. The…

view full answer...

Answer 4

We have some options for ball mounts that have a 6 inch rise. Curt ball mount #C45090 has a 6 inch rise and when in the rise position it is rated for 3,500 pounds gross trailer weight and 350 pounds tongue weight. The rise is measured from the top of…

view full answer...

Answer 5

The longest shank we offer is part #EQ90-02-4600 from Equal-i-zer which is 18 inches long overall or 14 inches from the center of the hitch pin hole to the centers of the adjustment holes on the shank. As it sits, the center of the hitch pin hole to…

view full answer...

Answer 6

The weight is 20 lbs for the BedRug XLT Truck Bed Mat #XLTBMT19SBS that fits your 2024 Ram 1500 with a 6-1/2 foot bed. The 3/4 inch thick mat is indeed the thickest you can get for your truck, so it's going to offer the most materia and best…

view full answer...

Answer 7

When we spoke with our contact at Curt they said the only time they've heard of the Curt T-Connector #C86CR having issues is when one of the pins was loose on one of the connectors. They replaced the kit for the 2023 Mazda CX-30 and everything…

view full answer...

Answer 8

I made a picture showing 3 important measurements on the Draw-Tite adjustable ball mount #7390. The distance from hitch pin hole center to ball hole center is 11-3/4 inches. If the extra 2 inches is needed in a ball mount then of course it would be…

view full answer...

Answer 9

I sent you a separate email with the instructions for installing the EcoHitch Hidden Trailer Hitch Receiver #EH55VR on your 2023 Mazda CX-30. I do recommend installing the 4-Way #C86CR when you install the receiver. The instructions for this are…

view full answer...

Answer 10

The second pin hole of the Curt ball mount part #C45240 that you referenced is 3 inches behind the first one. That means the second pin hole is 6-1/4 inches from the weld bracket.

view full answer...

Answer 11

The Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2" Hitches #ERT00108 requires at least 1" of the shank to properly fit. I went out and measured the shank on the Curt Adjustable 2-Ball Mount #C99NR and found the from the center of…

view full answer...

Answer 12

Just to make sure we are accurate on the actual rise you may need, lets cover some basics. With the tow vehicle parked on level ground, measure from the ground to the top of your hitch receiver opening. Then, with the trailer level, measure from the…

view full answer...

Does Etrailer Adjustable Hitch E66PR Fit 2024 Nissan Frontier With OEM Receiver?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching