Recommended Vent Cover for a MaxxFan Roof Vent 4301K

Question

Question:

Hi i am interested in your part number MA00a4301k vent kit but would like to know what maxx air cover can fit this part

asked by: Flavio A

0

Expert Reply:

Hey Flavio, for your MaxxFan Roof Vent w/ 12V Fan # MA00A04301K you can use the MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955001.

expert reply by: Bryce D

0

Robin H.

12/22/2025

Hey Flavio, how did the FanMate roof vent cover work with your MaxxFan vent? Knowing how the fit turned out could help others looking for the same setup.

Answer 1

We actually have a few different version of the white rain covers from MaxxAir. The MaxxAir II #MA76JR that you referenced comes with the pins. This is for applications where the roof vent has the mounting tabs on one side. Since you have the 4…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 10

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...

Answer 11

Hey James, we have the Curt hitch part #C34FR62ZY as a confirmed fit for your 2026 Toyota RAV4. This fits the hybrid and the PHEV versions BUT it's on a bit of a backorder and won't be available for some time. Are you planning on doing some…

view full answer...

Recommended Vent Cover for a MaxxFan Roof Vent 4301K

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching