Recommended Self Tapping Screws for Mounting Brake Lines
Updated 12/22/2025 | Published 10/21/2024
Products Featured in This Question
Question:
I have a 1989 27inch galvanized boat trailer that came with no brakes. The frame uses 3x2inch profile beams. I bought these rubber hose lines, but Im not sure where should I install them: on top of the beam so dirt and rocks can hit them as I drive down the road or on the side so I steep in the frame without stepping into the hose? Whats the best location? Also, what type of self tapping screws should I use to secure the line? These beams are thick.
asked by: David
Expert Reply:
Hey David welcome back! I would mount the rubber hoses on the side of the frame, for the Kodiak Hydraulic Brake Line Kit item # 20TA-BLKIT. To attach the line holders, I recommend the Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc item # FA1131822.
Product Page this Question was Asked From
Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1.5'
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 1-1/2 Feet Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Kodiak
more information >
Continue Researching
- Search Results: brake bleeder
- Search Results: bleeder
- Search Results: scissor jacks
- Search Results: deemaxx brake line
- Q&A: Recommended Disc Brake Hubs, Lines, and Hydraulic Actuator for a Boat Trailer w/a 3,500 lbs Axle
- Search Results: deemax brake line
- Shop: Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Zinc - 2" Ball - 7,000 lbs
- Shop: Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc
- Shop: Trailer Wiring
- Video: Kodiak Hydraulic Brake Hose Feature Review
- Shop: Dexter Premier Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Video: All You Need to Know About the Self-Tapping Screw
- Search Results: demco actuator
- Search Results: deemaxx brake lines
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Video: Comprehensive Review: Scissor Stabilizer Jacks w/ Handle
- Video: Feature Breakdown: Scissor Stabilizer Jack
- Shop: Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4
- Q&A: Is Capacity of Stabilizing Scissor Jacks Combined or For Individual Jack
- Q&A: Gauge Steel Used for etrailer Scissor Stabilizer Jacks, Mounting Hardware, and Base Pads
- Video: Complete Breakdown of the Titan Zinc-Plated Brake Actuator w/ Electric Lockout
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Q&A: Bleeding Trailer Brakes After Installing Kodiak Disc Brake Kit
- Q&A: Adding Brakes To A Shorelander Single Axle Boat Trailer
- Q&A: Recommended Disc Brake Upgrade for Boat Trailer
- Q&A: Will Demco Disc Brake Actuator Put Out Enough Pressure for Kodiak Disc Brakes
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Shop: Powerbuilt Brake Bleeder - Master Kit
- Video: A Closer Look at the Powerbuilt Brake Bleeder
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Triple Lip Grease Seal Kit - DX49CR
Jerred H.
12/22/2025
Hey David, how did the side-mount setup for the brake hoses on your boat trailer turn out? Did the self-tapping screws hold well in those thick beams? Your update could make it easier for others working on similar frames.