Installing NOCO Battery Box

Question

Question:

Where do the mounting brackets and screws go? It is not obvious. Thanx!

asked by: Jack R

0

Expert Reply:

The two mounting brackets included with the # 329-HM300BKS battery box would fasten to the mounting surface, using the included screws (or suitable hardware of your choosing) and the straps would be threaded through. The battery box would be placed on top of the straps, which would then be looped around the top of the box then buckled into place. Pretty easy, but I can understand why it wasn't obvious from the description photos.

expert reply by: Mike L

0

click to enlarge

Answer 1

What you described is actually the best solution! Connecting your battery to 12V Power wire from the 7-Way on your trailer is a great way to provide a maintenance charge on your battery to operate a Bulldog jack like part #BD500199. Mounting a…

view full answer...

Answer 2

If the jack drew less than 10 amps the Bright Way Push-to-Test Trailer Breakaway Kit with 2-Amp Charger and 10 Ah Battery #3802311 would work decently but typically they draw more than that. A better option would be a deep cycle battery like the part…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

The holes on the bottom of the TorkLift PowerArmor Locking Battery Box #TLA7700L aren't necessarily designed for mounting the box and are really there to allow moisture to escape and as access holes for wiring. According to the instructions there…

view full answer...

Answer 10

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 11

Thank you for reaching out! The best thing for your situation is to go with the 3,500 lb Dexter Axle #T3584F-8974 you are looking at. While you can upgrade your axles to the 5,200 lb #e55GR, you won't really see a benefit from it unless you also…

view full answer...

Installing NOCO Battery Box

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching