Troubleshooting Holes Not Lining Up On Curt Front Hitch 31322
Updated 08/31/2026 | Published 10/04/2024
Question:
I bought a 31322-bk front hitch and the final bolt at the end of the hitch to the cross member of the frame does not fit. I have been a mechanic for years, I have all bolts very loose and even used a 30 inch clamp to try to pull the hitch so the holes would line up, NO JOY. What is your recommendation?
asked by: Randy K
Expert Reply:
Hello Randy, you are referring to the single bolt that installs on the forwardmost part of the hitch (pictured below), is that correct?
How much is the hole off by? If it is off by a small about you can use a drill to enlarge the hole slightly if that helps get the bolt through. These hitches are made of a mild flex steel so it is not uncommon for them to bend slightly. If you are able bend the piece of the hitch back into position that will be fine too, just do so carefully. If you are not able to bend it back, or if it seems like the hole was drilled wrong during manufacturing, we will have to replace the hitch. The # 31322 is the correct hitch for the 2012 Chevy 1500, so it should be fitting. Let me know if I can do anything else to help.
Product Page this Question was Asked From
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Concealed Cross Tube
- 500 lbs Vert Load
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Front Mount Hitch
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Suspension Enhancement
- Search Results: front hitch
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Vertical Receiver Adapter - 2" to 2", 4-1/4" Long, 2-7/16" Drop
- Search Results: aux fuel tank
- Shop: Master Lock Trailer Hitch Receiver Lock - Swivel Head Design - 2" Hitches
- Shop: Trailer Wiring
- Search Results: trailer connector
- Search Results: connector
- Shop: Timbren Suspension Enhancement System - Rear Axle
- Video: Review of InfiniteRule Trailer Hitch Lock - 2-1/2 Inch B And W Tow And Stow And Pintle - IR52FR
- Search Results: sumosprings
- Search Results: b&w hitch pins
- Search Results: suspension enhancement
- Video: Front Runner Flat Upright Water Tank: The Breakdown
- Video: Checking Out the etrailer Anti-Rattle Locking Hitch Pin
- Video: In-Depth Review of the Front Runner Overland Water Tank
- Video: Andersen Hitch Locks - Standard Pin Lock - AM3492 Review
- Video: What to Know About the Roadmaster Hitch Extender for Tow Bars
- Shop: MOLLE Panel for Kuat Ibex Truck Bed Racks - Full-Height - 75-1/2" Wide x 20-1/2" Tall
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Vehicle Cargo Control
- Video: Pacbrake Alpha Air Bag Suspension Kit Review and Comparison
- Q&A: What Electrical Components are Needed to Install Detail K2 Elite Snow Plow
- Q&A: Recommended Front Hitch for a 2008 GMC 1500 4x4 that Provides the Most Clearance
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What are Fit Differences Between Curt Front Hitches C31012 and C31069
on Front Receiver Hitch
Jesse M.
12/22/2025
Hey Randy, how did things turn out with the Curt front hitch on your Chevy 1500? Did enlarging the hole or bending the hitch slightly help the bolt line up? Your update could make it easier for others running into the same fit issue.