Weight of the Curt Trailer Hitch Receiver

Question

Question:

hi, i need to know the weight of your class 3 hitch for a 2018 odysee so i can factor it into my payload and towing capacities. thanks.

asked by: Arron G

0

Expert Reply:

Hey Arron, the Curt Trailer Hitch # C13370 weighs approximately 34.34 lbs.

expert reply by: Bryce D

0

Robin H.

12/22/2025

Hey Arron, did that 34-pound weight help you figure out your Odyssey’s payload and towing numbers? Knowing how it worked out could help others planning a similar setup.

Answer 1

Hi Barney! I have the six hitches we have available for your 2019 Toyota Highlander listed below with their corresponding weights: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e98844 - 43.68 pounds…

view full answer...

Answer 2

The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e98907 weighs approximately 25lbs and has a maximum gross trailer weight capacity of 3,500lbs and maximum tongue weight 350lbs.

view full answer...

Answer 3

You definitely want all of the hardware installed for hitch #C13272 or any hitch because how it attaches is part of how it gets its rating. It sounds like the problem you are having is a factory weld nut that is packed with grime and corrosion.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Weight of the Curt Trailer Hitch Receiver

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching