Air Lift Air Bags and Cradle for 2024 Nissan Titan XD

Question

Question:

I need to know that the 88229 part will fit my 2024 Titan XD gas. I am also interested in knowing what cradle is compatible for full suspension travel. Please and thank you!

asked by: Doug

0

Expert Reply:

Hello Doug; the Air Lift LoadLifter 5000 # AL88229 is confirmed to fit your 2024 Nissan Titan XD. The correct cradles are the Air Lift Air Helper Spring Cradle # AL59DQ.

I also recommend adding an air compressor like the Air Lift WirelessAIR Compressor System # AL58WQ. This will allow you to adjust the air bags from the cab of your truck no matter where you travel. It is a dual path system so you can adjust the pressure in each individual air bag.

expert reply by: Robin H

0

Robin H.

1/5/2026

Hey Doug, how did the Air Lift LoadLifter 5000 and the cradles work out on your Titan XD? Did the setup give you the full suspension travel you were looking for? Your update could make it easier for others working on the same truck.

Doug

1/5/2026

@RobinH It was a perfect fit and so far I have been using it to tow a 30 foot travel trailer with 0 issues. It has actually improved the XDs ride when empty. It has minimized the HD bounce you get with heavier trucks. I absolutely highly recommend any XD owner to set this up.

Answer 1

No, they do not but I have a set that does. Instead you will want the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL88229. These also have a 5,000 lbs load leveling capacity that will keep the rear end of your 2023 Nissan Titan from…

view full answer...

Answer 2

For your 2018 Nissan Titan XD I recommend the Air Lift LoadLifter 5000 part #AL88229 which is a custom fit for your truck because it can provide up to 5,000 lbs of suspension support and it has internal jounce bumpers as well for added support. For a…

view full answer...

Answer 3

I have attached a sheet which shows the torque specs for wheels you can use when putting a tire and wheel. For 1/2" wheel bolts on a 13" aluminum wheel the torque is 75-85 ft.-lb. For lug nuts you can use the Lionshead Trailer Wheel Lug Nut…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Matt, welcome back! The Rock Tamers Adjustable Mud Flap #RT67VR is designed for a 2" receiver. The factory hitch on your 2024 GMC Sierra 3500 is 2-1/2" so you need the #ERT00110 instead. If you want the option with the screen that would…

view full answer...

Air Lift Air Bags and Cradle for 2024 Nissan Titan XD

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching