Recommended Hub for a Axle w/ a L44643 Inner and Outer Bearing and a 5 on 4-1/2" Lug Pattern
Updated 01/05/2026 | Published 09/16/2024
Products Featured in This Question
Question:
Jerrod, My existing hub is noted as EM1000 and does not have bolts protruding from it, rather the nuts are attached via tapped holes. The bearing number was L44643. From what you have stated, then I would need to swap out the hubs. Would your Easy grease Trailer idler hub assembly for a 2k axle 13-15 tire, 5 bolt 4 1/2” pitch Pregreased with cup ? Thank so much, Bill
asked by: Bill
Expert Reply:
Yes, it would Bill! The Easy Grease Trailer Idler Hub Assembly item # AKIHUB-545-2-LFEZ-1K you referenced is exactly what you'll need. It uses item # L44643 inner and outer bearings and has a 5 on 4-1/2" lug pattern. This hub is sold individually and is rated for 2,000 lbs axles.
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 13" to 15" - 5 on 4-1/2 - PreGreased
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- Pre-Greased
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Video: Easy Grease Trailer Idler Hub Assembly for 2K Axles Spec Review
- Article: How to Determine Tire/Wheel Diameter
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 13" to 15" - 5 on 4-1/2 - PreGreased
- Search Results: stickers
- Search Results: hitch wiring tester
- Search Results: l44643 / l44643 trailer hubs and drums
- Q&A: Trailer Idler Hub for 2,000 Pound Axle and 13 Inch Tires
- Video: Complete Breakdown of the Trailer Idler Hub Assembly for 2K Axles
- Shop: Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Replacement Trailer Hub Bearing - L44643
- Shop: Brophy Circuit Tester for 4-Pole Flat Trailer Connector
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Article: Trailer Tire Sizing
- Q&A: How Far Apart Are The Bolt Holes On etrailer Scissor Jacks e56VV ?
- Q&A: Replacement Bearing Solution for DICO Hub 45263
- Q&A: Hubs for 1" Straight Spindle With 5 on 4-1/2 Bolt Pattern Using 13" Wheels.
- Article: Trailer Lighting Requirements
- Q&A: How to Establish Ground Connection When Re-Wiring Aluminum Trailer
- Q&A: How To Remove Trailer Taillight that is Recessed Mounted in a Grommet
- Article: How to Measure a Trailer Axle
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How To Measure And Replace Everything In Your Hub Assembly
- Article: Trailer Maintenance Schedule
Jerred H.
1/5/2026
Hey Bill, how did the Easy Grease trailer idler hub assembly work out on your 2,000‑lb axle? Knowing how the fit and performance turned out could really help others looking at the same setup.