Will The BulletProof Sway Control Platform BPH76RR Fit The Curt Channel Style Ballmount C45900
Updated 08/29/2024 | Published 08/26/2024 >
Products Featured in This Question
Question:
I currently have a Curt adjustable mount C45900 and am figuring out the best way to add sway control only. Can you tell me if the Bulletproof ball mount BPH76RR will fit in the Curt channel mount. The hole spacing appears correct at 2, I need the width of the BPH76RR to determine its fitment inside the channel. Thank you.
asked by: Mike L
0
Product Page this Question was Asked From
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- Two Balls
- 2 Inch Ball
- 2-5/16 Inch Ball
- Steel Shank
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 14000 lbs GTW
- CURT
more information >
Continue Researching
- Search Results: victron
- Search Results: bulletproof
- Search Results: curt sway bar
- Search Results: curt hitch ball
- Search Results: anti~sway bars
- Search Results: curt friction sway control
- Search Results: sway control only weight distribution hitch
- Shop: Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel - 45 Amp
- Shop: Victron SmartShunt Battery Monitor - 300 Amp
- Shop: Victron SmartShunt Battery Monitor with IP65 Protection - 500 Amp
- Shop: Victron SmartShunt Battery Monitor - 500 Amp
- Shop: Victron GX Touch 50 Display for Cerbo GX Communication Center - 5" Touchscreen
- Shop: Victron Cerbo GX Communication Center - Bluetooth - 12V
- Shop: Victron SmartSolar 100/30 MPPT Solar Charge Controller - 12V/24V - 30 Amp
- Video: Victron M10 Lynx Shunt VE.Can Step-By-Step Install
- Video: Review of Victron Smart RV - Monitoring System - VN89RR
- Video: Review of Victron Smart RV - Cerbo GX Communication Center - VN23VR
- Video: Review of Victron GX Touch 50 Display Cerbo GX Communication Center - VN49ZR
- Video: Review of BulletProof Hitches Trailer Hitch Ball Mount - Adjustable Ball Mount - BPH79MR
- Video: Comprehensive Review: Sway Control 2-Ball Platform for BulletProof Hitches Ball Mount
- Video: All You Need to Know About the Curt Ball Mount w/ Sway Control Tab for 2" Hitches
- Q&A: Can You Upgrade from 5 Bolt 15 Wheels to 16 Wheels
- Q&A: Is There An Upgrade Kit For Adding Strut Assist To MORryde RV Steps?
- Q&A: Can The Furrion Chill HE RV Air Conditioner Run Off Of 15 Amp Service
- Q&A: Does Furrion Chill HE RV AC Unit have Soft Start
- Q&A: What Replacement Converter Do I Need for a Series 7300 Model 7345 Converter?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: How Does The Furrion Chill Cube Thermostat Get Wired To The AC System
- Article: How to Measure for Trailer Hitch Drop


Mike L.
8/29/2024
In case it comes up again, it does take a little modification. I went ahead and got them from you because I saw both use a 3" channel. However the Bulletproof ball assembly has squared corners on the back, the Curt ball assembly has slight chamfers on the outside corners which allow it to clear the radiused corners of the channel. The channel Bulletproof channel bracket must either be slightly deeper or the corners are less radiused. The square corners on the Bulletproof assembly do not allow it to fit into the 3" channel fully enough to fit the pins through the holes, ie. it bottoms out. It's close, only needs an addition 1/8" or so. 1 minute with an angle grinder to chamfer the edges to allow it (the assy) to fit into the radii of the Curt Channel and all is good. So yes it can be made to fit.