Could Ventline RV Roof Vent Install on 1 inch Thick Roof

Question

Question:

The roof of my pop up is only 1inch thick. Can this be installed on it and I just won’t use the trim piece on the inside or is there a way to make it work for a 1 inch roof?

asked by: Scott L

0

Expert Reply:

Hey Scott, yes the Ventline Ventadome RV roof vent part # V2110SP-24 can be installed on an RV roof vent that is 1 inch thick. You would just need to trim down the garnish to 1 inch so that it wouldn't be too tall and you'd be set.

expert reply by: Jameson C

0

Answer 1

All trailer roof vents nowadays fit what is referred to as a standard roof vent opening, which is described as "roughly" 14-1/4" x 14-1/4" so the Ventline Ventadome Trailer Roof Vent #V2110SP-24 might be able to squeeze into a…

view full answer...

Answer 2

For your race trailer with aluminum roof panels it will seal on the edges with a Butyl Tape #AL64UV. Then you will use either a Non-Sag #AL33KV or Self-Leveling #AL68KV sealant to seal the mounting screws and edges of the aluminum roof panels to…

view full answer...

Answer 3

A 14-1/4-inch x 14-1/4-inch rough trailer roof opening is very common and we offer a whole range of complete vent assemblies and also replacement lids and other parts for this size vent. Vents that fit this opening size are 14 x 14 size and the…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 6

Hey Chip, yes I agree the metal lid of the Ventline Ventadome part #V2110SP-24 is going to hold up the best over time which would mean you wouldn't have to worry about replacing the lid for a very long time. How old is the trailer?

view full answer...

Answer 7

Most slides have EPDM rubber roofs but because EPDM is rubber it requires treatment each year to keep it soft and prevent shrinkage. You could replace it with TPO which is another synthetic rubber that will last longer than the EPDM. The smallest…

view full answer...

Answer 8

I walked out to our warehouse and pulled the Ventline Ventadome Trailer Roof Vent, part #V2110SP-24, from our inventory to measure. The outside edge of the vent flange measured approximately 16-1/2 inches square. The actual opening of the vent…

view full answer...

Answer 9

Hey Greg, thanks for reaching out. So we do offer a few other 9/16" - 18 wheel studs that will be of sufficient length. The spline diameter of our studs is 0.689" though. We have nothing in that size with a 0.617" spline diameter or…

view full answer...

Answer 10

Hey Frevent! B&W does have options for a 2-1/2" hitch that work with the MultiPro but the rise/drop is going to be a little bit more. We have the B&W Tow & Stow 2-Ball Mount #BWTS20066BMP with a 7" drop/7-1/2" rise or the…

view full answer...

Answer 11

The RV Roof Repair Tape part #QR34FR works best when the existing tape is removed and it can be applied to a clean, bare surface. It can however be applied over the existing tape if you are in a bind.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Could Ventline RV Roof Vent Install on 1 inch Thick Roof

Product Page this Question was Asked From

Continue Researching