Replacement Recommendation for an Atwood 85736 Actuator
Updated 02/03/2026 | Published 07/29/2024
Question:
I’m looking for a brake coupler to replace my Atwood 85736 on 2003 Ebbtide tandem trailer. It has three linear holes with 3” spacing close to bottom edge of coupler. Thanks!
asked by: John H
Expert Reply:
Thanks for reaching out, John!
I recommend using the 7K Demco Hydraulic Brake Actuator # DM72VR as a replacement for your Atwood 85736 because of the EZ-Latch system on this coupler that makes it easier to use. The linear bolt holes on this are 3" apart on center and then there is a 3rd bolt hole in between them that you'll need to drill for. Unfortunately, drilling new holes for a replacement actuator is a pretty common thing.
Product Page this Question was Asked From
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Drum Brakes
- No Lockout
- Demco
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Search Results: horse trailer butt bar
- Q&A: Looking To Replace My Attwood Master Cylinder 85736
- Search Results: warning light emergency vehicle lights
- Search Results: tail light grommet
- Search Results: 4 round led tail light
- Search Results: 2 inch round led marker lights
- Shop: Trailer Hitch
- Video: What to Know About the Demco Hydraulic Brake Actuator-DM72VR
- Shop: Fifth Wheel Hitch
- Search Results: tekonsha prodigy
- Search Results: 902503
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Disc
- Shop: Reverse Lockout Solenoid Kit for Demco DA66B and DA70 Hydraulic Brake Actuators - Non-Bypass
- Shop: Reverse Lockout Solenoid Kit for Demco Hydraulic Brake Actuators - Non-Bypass
- Shop: Gooseneck Hitch
- Shop: DeeMaxx 13" Hub-and-Rotor Assembly - 8 on 6-1/2 - Maxx Coating - 8,000 lbs - 5/8" Studs
- Shop: DeeMaxx 13" Hub-and-Rotor Assembly - 8 on 6-1/2 - Maxx Coating - 8,000 lbs - 5/8" Studs
- Shop: Kodiak 13" Hub and Rotor - 8 on 6-1/2 - Dacromet - 9/16" Bolts - 7,000 lbs to 8,000 lbs
- Q&A: Replacement Actuator for an Older Atwood 85736
- Video: All About the Demco Hydraulic Brake Actuator-DM72VR
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Q&A: Replacement Surge Brake Actuator For Atwood 85736 That Is Discontinued
- Q&A: What is the Difference Between a Manual Lockout and No Lockout Brake Actuator
- Q&A: Solution for Atwood Surge Brake Coupler Needing Replacement Parts
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Article: How to Bleed Your Trailer Surge Brakes
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Brake Actuator
Jameson C.
2/3/2026
Hey John, how did the swap to the Demco brake actuator go on your Ebbtide trailer? Did the bolt pattern and drilling work out the way you expected? Your update could make it easier for the next person replacing an Atwood coupler.