What Replacement Hitch Bolt Works With The Yakima HangTight 6 Bike Rack?

Question

Question:

Which replacement hitch bolt works with a Yakima Hang Tight 6?

asked by: James S

0

Expert Reply:

Hello James, thanks for reaching out. The Replacement Anti-Rattle Hitch Bolt # Y52FR is the correct replacement for the Yakima HangTight 6 Bike Rack # Y39GR. If you need a new lock to go with the bolt, that is part # Y07235.

expert reply by: Jesse M

0

Jesse M.

2/3/2026

Hey James, how did the replacement hitch bolt work with your Yakima HangTight 6? Your update could make it easier for others trying to find the right fit for their rack.

Answer 1

For a replacement hitch bolt that is confirmed to work with your Yakima Roc 4 Bike Rack, I recommend the part #Y8890200. This threaded bolt is designed for the shank on your existing rack and includes the washer and clip. Then, to lock the hitch bolt…

view full answer...

Answer 2

Hey Paul, that we are aware of there isn't a different brand of hitch lock that works with any Yakima racks like the OnRamp part #Y88DJ. We've not had any issues with them being easier to defeat than other options or that they get gunked up…

view full answer...

Answer 3

I'd be happy to help you with that. You'll need the #Y52FR hitch bolt along with the #Y07235 HitchLock. Both are compatible with your #Y02484 Yakima HangOver 4 bike rack.

view full answer...

Answer 4

Possibly, it depends on what you have. I tried a few different socket sizes on the Swagman locking anti-rattle hitch pin, part #S64027, and found the actual fit to be a 23 millimeter which is a fairly uncommon size to use. You might be best using an…

view full answer...

Answer 5

Hello Bob, I can most definitely help. Since you now have a 2" receiver, you will want the Replacement Hitch Bolt for Yakima HoldUp 2, OnRamp, and BigHorn Bike Racks and DryDock Canoe Carrier #Y8890200. Do you have a specific trail you like to…

view full answer...

Answer 6

Hey Ak, thanks for reaching out! The Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR has a 4-5/8" overall length. I've attached a photo of this for your reference. Are you needing to replace the hitch pin…

view full answer...

Answer 7

Dan, the bolt you're looking for is the Replacement Hitch Bolt for Yakima HoldUp 2, OnRamp, and BigHorn Bike Racks and DryDock Canoe Carrier #Y8890200. This is a direct replacement for your archived ROCn'Gate.

view full answer...

Answer 8

The Yakima Replacement Hitch Bolt, part #Y8890176, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 9

Hey Jim, If you're needing something right away the Thule hitch pin lock #TH62RE has the same M12 x 1.75mm thread pitch as the original RockyMounts hitch pin and I physically tested it with the lock #RKY12006 and found that it's compatible.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Replacement Hitch Bolt Works With The Yakima HangTight 6 Bike Rack?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching