How Do I Install The Replacement Tailgate Seal for Pace Edwards UltraGroove Tonneau Cover PE84AJ

Question

Question:

Hi how do I install this? Replacement Tailgate Seal for Pace Edwards UltraGroove Retractable Tonneau Cover part PE84AJ. I found the seal grove is really hard to be opened to hook up on my tonneau cover end. Do you have a video how to get it on there?

asked by: Mark W

0

Expert Reply:

Hello Mark. Here are the steps for replacing the # PE84AJ Tailgate Seal:

- Remove plastic rail end caps

- Overextend cover a few inches past end of rails

- Slide old TG seal out of groove

- Using soapy water and slide new TG seal in from beginning of groove

- Trim so there is an 1/8” gap between ends of TG seal and rail sweep seal. You do not want TG seal touching rail sweep seals

expert reply by: Jesse M

0

Mark W.

7/30/2024

Thanks Jesse. I have the Leer Electric Retractable cover. How do I remove the end cap? I saw 2 screws at the bottom, but after removing the screws, i still found it hard to remove the end cap.

Mark W.

8/9/2024

Thanks Jesse. I have the Leer Electric Retractable cover. How do I remove the end cap? I saw 2 screws at the bottom, but after removing the screws, i still found it hard to remove the end cap.

Jesse M.

8/15/2024

@MarkW I went and looked at one of the Leer Electric Retractable covers and the two screws appear to be the only thing holding the end cap on so with those removed you should be able to get the cap off. Maybe see if some WD40 helps get them loose. A bit more force might do the trick. Don't break anything though.

Answer 1

The part #PE99CV is a totally different seal design from the part #PE92TJ which is a bulb style. They both are tailgate seals for the Pace Edwards Bedlocker but the part #PE99CV is a sweep style seal and the part #PW92TJ is a bulb style. If what you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How Do I Install The Replacement Tailgate Seal for Pace Edwards UltraGroove Tonneau Cover PE84AJ

Product Page this Question was Asked From

Continue Researching