TorkLift Tie-Down Fitment for a 2024 Ford F-350 Super Duty 6-3/4' Bed

Question

Question:

What is the correct part number for frame mounted tie downs for 2024 F-350 SRW 6.75’ bed?

asked by: Terry B

0

Expert Reply:

Hey Terry, thanks for reaching out!

The front tie-down for your 2024 Ford F-350 Super Duty is the TorkLift # TL77CR, and then for the rear position it all depends on the configuration of the back of your truck:

- Tie-Down # TLF3008 fits if you have a factory installed hitch
- Tie-Down # TLR3500 fits if you have a non-Torklift aftermarket hitch
- Tie-Down # TLR3504 fits if you have a Torklift SuperHitch Magnum 30k hitch

You'll also want to pick up some turnbuckles like the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK to secure your camper to all 4 tie-downs.

expert reply by: Jon G

0

Jesse M.

2/3/2026

Hey Terry, how did the TorkLift tie-downs work out on your F-350? Did the front and rear sets line up well with your truck’s frame? Your feedback could really help others setting up a similar camper rig.

Terry B.

2/3/2026

@JesseM The fast guns work fine. They do not prevent side to side movement of the camper such as occurs when traveling on a rough, off camber road. I built a 2x4 frame inside the truck bed to keep the camper centered. The fast gun also blocks the fuel door on the pickup bed. I disconnect it when filling with fuel.

Jesse M.

2/4/2026

@TerryB Hey Terry, thanks for sharing! You know I never thought about how the FastGuns could block the fuel door, that's a great call out. I bet its actually fairly common with these new Fords. Good call on building a frame inside the truck bed too. Sounds like you nailed it and got you setup dialed in perfectly. Thanks again for the feedback!

Answer 1

Hey Lonnie! The correct rear tie-downs for your F-250 once you add the TorkLift SuperHitch Magnum #TLF1008-30 are the #TLR3504. What made you decide to upgrade to the TorkLift hitch?

view full answer...

Answer 2

Hey Keith! The TorkLift Talon Truck Camper Tie-Downs item #TL25SV combo will fit your 2025 Ford F-350 if your truck has the TorkLift SuperHitch Magnum 30k item #TL27CR installed. If you have the factory hitch or an aftermarket hitch you'll need…

view full answer...

Answer 3

I have a solution for you but there isn't just a replacement converter section for the Elixir ELX-45. You're going to need to replace the entire panel with the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger item…

view full answer...

Answer 4

To replace your Airstream's current axles you need to determine their weight capacity and the hub face and spring center lengths. Unfortunately, we don't have a way of knowing exactly which replacement parts fit your trailer without…

view full answer...

Answer 5

I have attached for you below the shipping weights of each item you requested. The actual weight can be found by simply subtracting a few lbs for shipping material. TorkLift Custom Frame-Mounted Camper Tie-Downs - Front part #TLF2021 (42 lbs)…

view full answer...

Answer 6

Levi, for your 2024 Ford F-350 you can use the TorkLift Camper Tie-Downs #TL77CR for the front and #TLF3008 for the rear. These are custom frame mounted tie downs that will bolt right up to your frame, and includes all the mounting hardware for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

TorkLift Tie-Down Fitment for a 2024 Ford F-350 Super Duty 6-3/4' Bed

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching