Peterson Clearance Light M116A - Can The Incandescent Bulbs Be Replaced With LED Bulbs

Question

Question:

Are the incandescent bulbs inside these replaceable with an LED bulb?

asked by: Cooper G

0

Expert Reply:

Hello Cooper. Yes, you can replace the incandescent bulbs inside the Peterson Clearance or Side Marker Trailer Light # M116A with LED bulbs.

expert reply by: Jesse M

0

Jesse M.

2/17/2026

Hey Cooper, how did the LED bulb swap go with your Peterson trailer light? Your update could make it easier for the next person looking to upgrade their lights.

Answer 1

Hey Joe, The closest light I can find to the size of your current Wesbar is the Peterson #M116A, which comes in at 5-3/8" x 1-13/16". It does use a 2 hole mount so you would need to drill another hole in order to install. We do not carry…

view full answer...

Answer 2

Hey Mike! The closest amber LED light I have to what you're looking for is the Peterson Clearance or Side Marker Trailer Light w/ Reflector item #M116A. It has mounting holes that are 3-1/8" on center. Most of our amber LED clearance lights…

view full answer...

Answer 3

The closest LED light that we have to the #M116A is the Triangular LED Trailer Clearance and Side Marker Light or Truck Cab Light, 15 Diode - Amber #CBL22AB. This has a wider design and is not reflective. This is a very nice light that I recommend if…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Peterson Clearance Light M116A - Can The Incandescent Bulbs Be Replaced With LED Bulbs

Product Page this Question was Asked From

Continue Researching