Need Trailer Hitch To Fit A 2011 Ford Fusion

Question

Question:

Yes you are correct. I’ll confirm the numbers but when I looked at the instructions that was the vehicle it fits. I need a hitch to fit 2011 ford fusion

asked by: Brian H

0

Expert Reply:

Hello Brian. The Draw-Tite Class 1 Hitch # 24865 is what I recommend for the 2011 Ford Fusion. It is an easy bolt on install and it is confirmed to fit all models of the 2011 Fusion, including the Hybrid. I have included a link to an install video for you below.

Let me know if you have any other questions or if there is anything else you need.

expert reply by: Jesse M

0

Answer 1

As long as you have the needed wheel well and trailer frame clearance, there is no reason that you couldn't go to a larger tire size from your existing 5.30-12 tires. The next size up from what you have is going to be with an ST175/80-13 size…

view full answer...

Answer 2

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 3

Hey Lee, so in general the radial tire construction is preferred over the bias ply. You'll get a more stable ride and generally a little less heat build up. If you will be under the weight and speed capacity of your current tires I think…

view full answer...

Answer 4

Hello Bruno, thanks for reaching out. The Demco #DM72VR can be used to replace your old Atwood 61101. The Demco actuator uses 3 holes and you will need to use all three holes for mounting. If your tongue only has two holes currently, a 3rd hole will…

view full answer...

Answer 5

Yes, if you inserted a rod into the hole that in front of the housing of the actuator of the part #DM72VR that would work as a manual lock out and allow you to reverse the trailer.

view full answer...

Answer 6

For carrying a bike rack or cargo carrier the best option for a hitch is the Draw TIte part #24865. Reason being it does not require a stabilizer strap when carrying either rack like the Curt #C11390 does.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Need Trailer Hitch To Fit A 2011 Ford Fusion

Featured Help Information

Miscellaneous Media

Continue Researching