Installing A Reese Brakeman Controller In A 202 Ford E250 With Factory 4-Flat
Updated 05/24/2024 | Published 05/11/2024 >
Question:
I have a Reese Brakeman controller. I want to install it in a 2002 E250 van. Van has 4 pole flat factory wiring. Under the dash is a factory brake controller plug with 5 wires in it. Recommendations on what I need to complete the job.
asked by: John D
Expert Reply:
Hey John, I can definitely help with that. The Reese brakeman controllers are compatible with the Tekonsha brand plug-and-play adapters. For your 2002 Ford E250 you can use the # 3035-P to plug directly in to the factory brake controller plug. You will also need item # 37185 to complete your wiring. The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.
Product Page this Question was Asked From
Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV - 10 Gauge
- Custom Fit Vehicle Wiring
- Wiring Adapters
- Universal Fit
- 4 Flat to 7 Blade
- Plug and Lead
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: 12 gauge wiring
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Video: Beginner’s Guide to Installing the etrailer Trailer Hitch Receiver on a 2021 Subaru Ascent
- Video: An In-Depth Look at the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation
- Search Results: 4 pin to 7 pin conversion
- Search Results: heat shrink connectors
- Search Results: 11755
- Search Results: pk12711u
- Search Results: 18140
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Q&A: Fuse Box Instructions for Installing a Brake Controller on a 2003 Chevy Silverado
- Q&A: Location Of Under Dash Brake Controller Port On 2002 Ford F150
- Search Results: trailer hitch
- Q&A: Will etrailer Hitch Install for 2025 Subaru Ascent be the Same as 2021 Model Year?
- Video: Let’s Check Out the Curt Universal Installation Kit for Trailer Brake Controller
- Video: etrailer Trailer Brake Controller 7-Way RV Upgrade Kit Installation - 2020 Subaru Outback Wagon
- Video: Draw-Tite I-Command Trailer Brake Controller Installation - 2010 Jeep Wrangler Unlimited
- Video: etrailer Class III Trailer Hitch DIY Installation - 2022 Subaru Ascent
- Shop: Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV - 10 Gauge
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - Off-Road Mode - Up to 3 Axles - Proportional
- Q&A: Wiring and Brake Controller Needed for 1996 Ford F-150 with 4-Way Flat
- Q&A: What Is the Difference Between the etrailer and Curt Bolt On Trailer Hitches


John D.
5/15/2024
What additional wires and breakers and or fuse would I need and do you sell them?