Replacement AC Unit Recommendation for Carrier # 68RV14113A

Question

Question:

68RV14113A Is the model of the unit now what’s the replacement unit

asked by: Eric S

0

Expert Reply:

Hey Eric, the Carrier 68RV14102A is no longer available but we have the 15,000 Btu Advent Air Replacement RV Air Conditioner for a Carrier Setup, # ACCAR150 that is your best option that will allow you to replace what you have directly since it comes with the adapters needed to fit a Carrier setup.

The included adapter wiring kit ensures that the AC works seamlessly with your existing, in-good-working-order Carrier air distribution box and thermostat.

expert reply by: Jameson C

0

Answer 1

We've ran into this issue before, but unfortunately Kwikee/Lippert no longer manufactures that 151332 motor, and I'm sorry to say that they do not offer a replacement. I was unable to find anything about the 131320 part you mentioned either.…

view full answer...

Answer 2

It looks like the closest we have to those measurements is the Replacement Support Arm Assembly for Solera Pitched RV Awnings LC260294 which measures 66 1/8" long. Just to be clear, you will need to measure the wall mount from the top to the…

view full answer...

Answer 3

The 84 Series #34-84-008 and #30-84-008 are actually incandescent and not LED so you won't have any problems. For a similar light that does use LED you would want the Bargman #47-84-008. This uses an LED light for the brake/tail/turn signals but…

view full answer...

Answer 4

Hi Tim, So the Bargman 47-84-020 was discontinued, which is why you were unable to find it, and we do have a similar option that can replace it with the Dual LED Trailer Tail Light #CE86FR. The #CE86FR has the same functions as the Bargman - stop,…

view full answer...

Answer 5

Hey Wayne! Everything is switching to the new R32 refrigerant which isn't backwards compatible. It also means old R410A parts are disappearing so now is a good time to make the switch. Even if this wasn't the case, we stopped recommending…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement AC Unit Recommendation for Carrier # 68RV14113A

Continue Researching