Can Hubs of etrailer Axle part # e25GR be Used on Boat Trailer and Get Submersed

Question

Question:

Are the hub’s submersible for a boat trailer

asked by: Keith S

0

Expert Reply:

Hey Keith, yes the hubs on the Trailer Axle part # e25GR are submersible so you can use this axle on a boat trailer.

expert reply by: Jameson C

0

Answer 1

The bushings for the slipper springs in your Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles #RM-2460-2570 would not need grease so you can definitely swap out the wet bolts with some standard bolts…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The Timbren Trailer Suspension Enhancement System part #TTRA1032 is my recommendation for a set of bump stops or jounce bumpers for a Dexter 7K Axle. These Timbrens will do a great job of compensating for off-center loads, reduces body roll when…

view full answer...

Answer 11

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using has a…

view full answer...

Answer 12

The replacement ladder I recommend for your 2017 Thor Siesta 24SS is the Stromberg Carlson RV Exterior Ladder w/ Hinges - Aluminum - 99-1/2" T x 12" W - Black #LA-401BA. The reason I recommend this replacement ladder is because it is an…

view full answer...

Can Hubs of etrailer Axle part # e25GR be Used on Boat Trailer and Get Submersed

Product Page this Question was Asked From

Continue Researching