Does etrailer Coupler # CTA-400 Have Adjustable Latch

Question

Question:

Trailer Coupler - Adjustable Channel Mount - Thumb Latch - Black - 2-5/16 Ball - 14,000 lbs Question is there adjustments to tight de ball socket if lousse ? Thanks

asked by: Claude G

0

Expert Reply:

Hey Claude, the latch mechanism of the etrailer coupler part # CTA-400 is not adjustable but it's not like lighter duty couplers that are going to get loose over time to the point the coupler could let go of the ball.

expert reply by: Jameson C

0

Claude G.

4/18/2024

Thanks

Answer 1

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 2

I went out to the warehouse to measure the mounting holes on trailer coupler #CTA-400. They measure 0.66 inches in diameter. This coupler does come with the mounting hardware as well. I have included a link to a video review of this coupler for you.

view full answer...

Answer 3

The etrailer Trailer Coupler #CTA-400 uses the Replacement Mounting Bolt with Nut for Adjustable Channel Couplers #MBT58500-LN58. This is a 5/8" grade 8 bolt. I have attached a diagram below which shows the full dimensions.

view full answer...

Answer 4

Hello Tommy, good question. So the channel mount couplers like the Trailer Coupler #CTA-400 use grade 8 5/8" bolts to attach to the channel. It is not recommended to replace the bolts with pins, since there would be no way to add torque. You…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Does etrailer Coupler # CTA-400 Have Adjustable Latch

Product Page this Question was Asked From

Continue Researching