Can Air Lift Compressor Kit Handle 10 PSI

Question

Question:

I have the rough country air bag system 03 2500HD Silverado. 5000 pound 100 psi max. Will your compressor system be compatible? Also can I purchase an extra 1/4 inch tee connector and a couple extra 90 degree elbows that screw into the top of the bag and connects to the 1/4 inch air line?

asked by: William F

0

Expert Reply:

Hey William, so the Air Lift Air Shock Controller Compressor System for Air Shock Absorbers # AL25804 that you referenced is rated for up to 160 psi so it would easily handle 100 psi. For a union tee fitting you'd then want the part # F3025-1.

If you have an Air Lift air bag the correct replacement elbow fitting is the part # AL52RV.

expert reply by: Jameson C

0

William F.

4/10/2024

Excellent I'll order tomorrow

Jameson C.

4/11/2024

@WilliamF Awesome!

Answer 1

The Air Lift Air Shock Controller Compressor, part #AL25804 includes the onboard compressor; dash mounted gauge panel; hardware and air lines. An air tank isn't included. Since the compressor is manually operated from the dash panel, a pressure…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Can Air Lift Compressor Kit Handle 10 PSI

Products Featured in This Question

Continue Researching