What Wire Needs to be Connected to Terminal 1 On the ICX Transmitter Relay
Updated 04/10/2024 | Published 04/09/2024 >
Question:
I have 2018 F150 with neutral tow. I have the older version Roadmaster Even Tow. I have installed the 88400 brake light relay using the “B” instructions on page 3 using the blue wire. My question is what wire do I use to go to the “terminal 1” on the ICX transmitter from the relay. I’m thinking it’s the blue also but want to make sure Thanks
asked by: Rick L
0
Expert Reply:
Hey Rick, you are correct the blue brake output wire would also need to be connected to terminal 1 for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles # RM-88400.
expert reply by:
Bryce D
0
Product Page this Question was Asked From
Roadmaster Brake-Lite Relay Kit for Towed Vehicles
- Flat Tow Brake System
- Brake Light Relay
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Vehicle Tow Bar Wiring
- Shop: Vehicle Tow Bar Brake System
- Q&A: Installing The Roadmaster Brake-Lite Relay Kit On A 2016 Ram 1500
- Q&A: Does Brake-Lite Relay Kit Work if You Forget to Turn Lights On
- Search Results: trailer hitch
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Search Results: trailer wiring
- Shop: Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Shop: Trailer Wiring
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Q&A: Which is Better Roadmaster or Blue Ox Tow Bar
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Q&A: Parts Needed to Install a Red Arc Brake Controller in a 2023 Toyota Tacoma
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Breaking Down the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Article: How to Measure for Trailer Hitch Drop
- Search Results: base plate for tow bar
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Base Plate for Tow Bar
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Replacing 6-Way on Trailer With 7-Way Connector


Rick L.
4/10/2024
So on the diagram figure 3 the brake signal out is connected to the icx terminal 1. After all is hooked up and functioning. Once the motor home is moved and motor home brake pedal depressed. Even break responds to deceleration of the motor home. Then after each time the motor home break is depressed. The icx terminal 1 would get voltage to activate the easy break to press the towed break. Correct? Not an easy way to pre test this other than to try? I’m just trying to make sure I have everything hooked up correctly