Longest Replacement Fenders for Featherlite Trailer

Question

Question:

Do you carry 74 wheel wells for featherlight trailers? Or can you find them ?

asked by: Matthew G

0

Expert Reply:

The closest we have are our 72" long fenders like the Tandem Axle Teardrop Trailer Fenders # HP74VR for 15" and 16" wheels. This should work as long as the fenders sit on the outside of the trailer body. If this is for an enclosed trailer where the wheel wells are built into the body of the trailer then you'll need to look into a direct replacement from Featherlite.

expert reply by: Jon G

0

Answer 1

Hello Juan, I think I found the solution for your 3110 Featherlite, the Tandem Axle Trailer Fenders for Enclosed Trailers #HP35VR, for a pair #HP52VR. Now I do not have a database that tells me what is put on what trailer, I did find on the…

view full answer...

Answer 2

Typically the max wear on a king pin is .080 of an inch with a minimum diameter of 1.920. DOT says the max wear is .125 of an inch with a minimum diameter of 1.875. When new the king pin will have 2 inches of diameter. See the image I made for you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Longest Replacement Fenders for Featherlite Trailer

Product Page this Question was Asked From

Continue Researching