Slide Topper For a GeoPro G20FBS With an 82" Slide Out

Question

Question:

I bought a geopro g20fbs. It has one slide out that measures 82 in. The manufacture installed the upper track for the fabric and the slide out brackets for the solera slide out covers. The upper slide track extends 6 in on one side past the slide out and 5 in on the other side. What slide out do I need to order. The dealer I bought the trailer from said I need 7ft but the fabric measurement will not completely cover the slide out. What is the correct slide out cover? 76? Do I have enough upper track and will the arms be long enough for a 76inch slide out cover?

asked by: John S

0

Expert Reply:

With your slide out having an 82" flange to flange measurement you want the Solera RV Slide-Out Awning # LCV000163287 which has an 85" wide fabric. The 91" # LCV000163288 you found will not have long enough arms for the mounting hardware to be properly secured.

expert reply by: Bud M

0

John

3/20/2024

Thanks for your help. I will need black. I understand the fabric will cover 85". That will be perfect. However the directions indicate I need 7" past the end of the side wall flange. I measured that I have approx 5.5-6 on each side. Will I be OK? What stock number do I order for the black? Same price?

Bud M.

3/28/2024

@John The 7" is for the hardware to clear anything like an awning or door opening. We do have the 85" in Black # LCV000165062. But if you do not have the clearance required because of an Awning or door opening we do have the smaller 79" # LCV000168105 in black as well. Do understand if you have 6" only on one side you can offset the awning to the other side slightly as well to stay with the 85" as long as it does not also interfere with the other side. You can always end me a image with the measurements for your camper and I can reassure you of which will be best. Sorry it took so long to get back to you as we had an issue with getting the comments on our end.

Answer 1

To select a slide-topper awning you'll want to measure the box width on the outside front of the box and include the flange. To order the correct Solera Slider select the fabric size that extends a minimum of 2-1/2-inches beyond each side of your…

view full answer...

Answer 2

The 2021 Nissan Rogue's have what's called rear automatic braking. It automatically applies the brakes and blares a screeching alarm if something is behind you. This is a great safety feature if you are backing up and someone walks out but it…

view full answer...

Answer 3

The Class III hitches we have for your 2022 Nissan Rogue include the Draw-Tite #DT85MR and the Curt #C24HR. I recommend going with the Draw-Tite over the Curt because it sits about 1/2" higher off the ground and the center of the hitch pin hole…

view full answer...

Answer 4

The Draw-Tite #DT85MR and etrailer.com #e93ZR Class III hitches will be evenly matched in weight capacities for your 2021 Nissan Rogue, so we can disregard the capacities for this comparison. Especially since your Rogue can tow, when properly…

view full answer...

Answer 5

The access plate is 2-15/16" wide and 7-5/8" long and must be mounted on the slide out's outside wall as far up as it can, but not mounted on the t-molding. The t-molding is what looks like 6" wide trim around the outside slide out…

view full answer...

Answer 6

If the width of the slide out on your Rockwood 2109s mini lite is between 80" to 85-3/4" including the width of the flange then the Solera Slide Topper #LCV000165062 will fit and work well. No install issues would arise at all. I attached a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Slide Topper For a GeoPro G20FBS With an 82" Slide Out

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching