How Much Torque to Install Timbren SES Kit TFRTT350F

Question

Question:

What are the recommended torque settings for the Timbren TFRTT350F? I do not see them listed anywhere.

asked by: Jim

0

Expert Reply:

Hey Jim, when installing the Timbren SES kit part # TFRTT350F 33 ft lbs of torque would be the correct amount.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Timbren and he said they don't have an official torque spec for the hardware on the Timbren Rear Suspension Enhancement System #TTORSEQ you referenced but tightening all the hardware to around 20 foot-pounds will be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Welcome back Leroy! The Dual Pin Lock for B&W Tow & Stow Pintle Mount item #BW72AR is the correct lock for the B&W Tow & Stow Pintle Hook item #BW77BR. The Dual Pin Lock item #BW72AR is going to attach in the center of the adjustment…

view full answer...

Answer 5

The difference in harshness between the Timbren kits part #TFR350SDF and #TFRTT350F would be very noticeable. Especially when unloaded. Your truck is already going to have a rough ride as that is the nature of 1 ton trucks but the 12k Timbren kit…

view full answer...

Answer 6

I contacted the technical staff at B and W to confirm compatibility of their Companion 5th wheel hitch with aftermarket rear suspension kits such as the Timbren Jounce Spring Kit #TFR350SDF in your 2008 F350. My contact there advised that a jounce…

view full answer...

Answer 7

We do not offer any custom gooseneck hitches for your F-350 Cab And Chassis, but we do have the Fold-Down Gooseneck Trailer Hitch with Installation Kit, part #8339. This hitch has a 25,000-lb gross towing capacity and includes a 2-5/16 inch ball. The…

view full answer...

Answer 8

Hey Charles, We should have some options for you. I will say I am not too familiar with a "top drive" style vehicle so I am interested to know a little more about that. It may determine what fits or doesn't fit as well. For air bags for…

view full answer...

Answer 9

The Northern Breeze V2525 Roof Vent and all of it's parts have been discontinued so the most cost effective and practical option is to just replace the unit entirely instead of rigging other vent parts to try and fit your needs. I recommend the…

view full answer...

Answer 10

Yes, you can still install the Timbren Springs #TFRTT350F on your 2013 Ford F-250 without the raised stop like you have seen in the images you found. I have included an image below which shows their other Kit #TFR250SDG for your F-250 on a truck…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

How Much Torque to Install Timbren SES Kit TFRTT350F

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching