Replacement Hitch Install Hardware for Draw Tite # 75782

Question

Question:

I went to put this draw tite hitch on my inherited car.parents 2015 Ford escape. They bought a hitch years ago for a scooter but never had anyone install it. I have it but cannot find the hardware. Any chance I can buy just the hardware kit?

asked by: Ryan B

0

Expert Reply:

We do sell replacement hardware for all of the hitches we carry with the part # RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

expert reply by: Jameson C

0

Ryan

3/16/2024

So #RHK ardware kit is for my hitch or every hitch?

Jameson C.

3/18/2024

@Ryan Not to be confusing...but yes and yes. It's a part number in our system that we use as a replacement hardware kit for all of the hitches we carry. But when you go to order it you just need to input the hitch part number that you have and we'll make sure you get the correct hardware for your hitch.

Answer 1

We can provide emplacement hardware to install a Curt #13650 Class III hitch on your 2008 Escape. You would use part #RHK. On the product pate, type the hitch part number into the provided field, choose Curt from the drop-down menu and choose a…

view full answer...

Answer 2

You will need to order a Replacement Hardware Kit #RHK. Once on the product page you will select Curt from the drop down box and put in the hitch number as 13650. This will give you the hardware you need for your Curt Trailer Hitch Receiver #13650.

view full answer...

Answer 3

We do have replacement hardware for the Curt #13650. The bolts are easy to come by, but since you need the square hole spacers you'll have to get the entire kit. What you need is the Replacement Hardware Kit for Trailer Hitches #RHK. Enter the…

view full answer...

Answer 4

The 6 bolts you should have received with the Curt Trailer Hitch Receiver #13650 are 1/2-13 x 1 3/4 carriage bolts with the 1-3/4 number meaning the total length of the threaded bolt. This isn't a common issue with the bolts not working but you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Hitch Install Hardware for Draw Tite # 75782

Products Featured in This Question

Continue Researching