Replacement Mounting Hardware For Curt Trailer Hitch Receiver # 13650

Question

Question:

Need mounting hardware kit for 13650 hitch.

asked by: B H

0

Expert Reply:

You will need to order a Replacement Hardware Kit # RHK. Once on the product page you will select Curt from the drop down box and put in the hitch number as 13650. This will give you the hardware you need for your Curt Trailer Hitch Receiver # 13650.

expert reply by: Bud M

0

Answer 1

We do have replacement hardware for the Curt #13650. The bolts are easy to come by, but since you need the square hole spacers you'll have to get the entire kit. What you need is the Replacement Hardware Kit for Trailer Hitches #RHK. Enter the…

view full answer...

Answer 2

We can provide emplacement hardware to install a Curt #13650 Class III hitch on your 2008 Escape. You would use part #RHK. On the product pate, type the hitch part number into the provided field, choose Curt from the drop-down menu and choose a…

view full answer...

Answer 3

Hey Mark we do have a hardware kit for the 13570 Curt Trailer Hitch our item #C69VV. It is the Replacement Hardware Kit for Trailer Hitches item #RHK. This kit has the carriage bolts, square-hole spacers, serrated-flange nuts, flat washers, and…

view full answer...

Answer 4

In order to obtain the bolts to attach the Curt Trailer Hitch Receiver part #13650 to a 2005 - 2012 Ford Escape, 2005 - 2011 Mercury Mariner, or a 2005 - 2011 Mazda Tribute you would want to use the Replacement Hardware Kit for Trailer Hitches part…

view full answer...

Answer 5

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 6

We do sell replacement hardware for all of the hitches we carry with the part #RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

view full answer...

Answer 7

The 6 bolts you should have received with the Curt Trailer Hitch Receiver #13650 are 1/2-13 x 1 3/4 carriage bolts with the 1-3/4 number meaning the total length of the threaded bolt. This isn't a common issue with the bolts not working but you…

view full answer...

Answer 8

To properly measure your leaf springs you'll want to lift the trailer by the frame to take the weight off of the suspension and then measure from the center of the eyelet straight across the spring to the end of the slipper (pictured below). From…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Mounting Hardware For Curt Trailer Hitch Receiver # 13650

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching