Installing A Redarc Tow Pro Liberty Brake Controller In A 2018 Toyota Sequoia Platinum

Question

Question:

I need a brake controller for a 2018 Sequoia Platinum with factory towing. 1. Do I need RED24FR or RED49FR? 2. What is the correct wiring harness adapter? 3. Do I need to buy a separate knob? Thanks

asked by: Steve A

0

Expert Reply:

Hi Steve,

1. # RED24FR is going to be just the brake controller and would still require a wire harness to connect to the vehicle. The # RED49FR is a custom-fit wire harness designed for your Sequoia that will make for an easy installation.

2. The # RED49FR is going to be the only wire harness you need and would plug directly into a connector hidden behind the kick plate to the left of your e-brake. I've attached a video below where Brad installs the other version of this brake controller and you can just follow along.

3. You won't need a separate knob but if you don't want to drill into the dash you should be able to pop out a blank in the dash and use part # 331-TPSI-002 to mount the knob.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The coil spring bags are designed to fit the stock coil springs. Unfortunately, you won't be able to use the existing #AL60743 air bags since the coil springs were replaced. You may be able to use the Air Lift 1000 Universal Air Spring Kit like…

view full answer...

Answer 3

There's no reason you'd have issues with 20 feet of propane line like you have. The pressure equalizes in the line so it's not like you'd have a pressure loss situation.

view full answer...

Answer 4

If you're right about taking the regulator off of the Blackstone griddle then you can use part #100476-120-MBS for a 10 foot hose that goes from the regulated quick disconnect on the trailer right to it. The Coleman on the other hand is more…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Installing A Redarc Tow Pro Liberty Brake Controller In A 2018 Toyota Sequoia Platinum

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching