Can Trailer Brakes be Added Torsion Axle

Question

Question:

I have a two into one jet ski trailer from Magic Tilt. These are two separate trailers that connect to become a double trailer. They have torsion axles not sure that matters. Is it possible to add brakes to these trailers? Thank you.

asked by: John A

0

Expert Reply:

Hey John, it is definitely possible to add brakes to a trailer with torsion axles but it comes down to whether or not the spindles of the trailer axles have brake mounting flanges currently as the biggest hurdle. They can be added but it's a little more involved. Next you'd need to know the axle capacity and the wheel bolt pattern and from there you'd have all info needed to add brakes.

If you check out the help article I attached you can see a guide that will walk you through the entire process of adding brakes to a trailer.

expert reply by: Jameson C

0

Answer 1

Hey, Tim! You can absolutely use a MouseBlocker on a truck you drive every day. MouseBlocker offers their classic unit, part #MB44FR, which works well for smaller equipment. While it can be used on your F-450, I think you’d be much happier with their…

view full answer...

Answer 2

In order to install a trailer brake controller on a 2015 Ford F-150, I recommend the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 which is one of the most popular and reliable options. It will also feature a plug-in install when combined…

view full answer...

Answer 3

There should be a factory brake controller plug on your 2015 Ford F-150, whether it came with a 4-Way or 7-Way connector at the back of the truck. The plug will be located beneath the dash inside your cab. You may need to remove some shroud around…

view full answer...

Answer 4

The Reese Towpower 8508211 is like the Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional #90885 that we offer. For a 2019 Ford Flex with the factory tow package, you'd want to use the #22292 brake controller wiring…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Can Trailer Brakes be Added Torsion Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching